| 101 | Located in Lexinton, KY -- | NEW/Unused Colorado Mill Equipment C10 Counterflow Cooler built-in 2019 with: Bottom discharge bin, rotary level sensor, 15hp blower air system with cyclone and airlock, top rotary valve, adjustable legs. Rated from 2-3 ton/hr up to 10-12 tons/hr depending on the product, ***NEW COST OVER $57,000***, Laoding fee $300 |
| 101A | Located in Lexinton, KY -- | C10 Control Panel for lot 101, Loading fee $30 |
| 102 | Located in Lexinton, KY -- | NEW/Unused Colorado Mill Equipment RE150 pellet mill with: 200hp motor main drive, stainless steel door with knife post, force feeder, new 1/4 die and rolls, hopper bin, and autolube system. ***NEW COST OVER $120,000***, Loading fee $300 |
| 102A | Located in Lexinton, KY -- | Control panel for Pellet Mill Lot 102, Loading fee $30 |
| 102B | Located in Lexinton, KY -- | Disconnects for 200HP Motor on Lot 102, Loading fee $30 |
| 103 | Located in Lexinton, KY -- | NEW/ Unsed Laughlin Product Conveyor, Loading fee $125 |
| 104 | Located in Lexinton, KY -- | Stainless vertical bin with air cylinder release into tote, Loading fee $200 |
| 105 | Located in Lexinton, KY -- | NEW/Unsed Annex Bratney Z bucket conveyor per drawing replacement purchase cost over $115,000, Loading Fee $100 |
| 106 | Located in Lexinton, KY -- | NEW/Unsed Laughlin Product Conveyor, wrapped in plastic (similar in size to lot 103), Loading fee $125 |
| 107 | Located in Lexinton, KY -- | NEW/Unused Small Pellet Transfer Conveyor, Loading fee $50 |
| 108 | Located in Lexinton, KY -- | NEW/Unused Small Pellet Transfer Conveyor, Loading fee $50 |
| 2000 | Located in Canon City, CO -- | THIS INDUSTRIAL PROPERTY is located just off of Forge Road in southwest Canon City. The property consists of 5.78 business zoned acres, a 56,279 sq. ft., single story heavy industrial building with dual overhead 5 ton cranes, 20x18 Paint Booth, 28x13 Sand Blasting room and a separate 4,922 sq. ft. single story office building for a total building area of 61,201 sq.ft. There is 230/460 electric service to several places in the building. |
| 2001 | Located in Canon City, CO -- | Pexto Slip Roll Machine 36" wide w/3"rolls, in operation, (can be seen under power at our plant) $100 load fee |
| 2002 | Located in Canon City, CO -- | Niagra Brake Press HD-55-6-8, 55ton brake, 8ft wide, in operation,(can be seen under power at our plant) $500 load fee |
| 2003a | Located in Canon City, CO -- | Wysong and Miles Shear, 12 gauge, 96" long, model 1296, 3 phase squaring shear, in operation, no#1296, 8' ft.long cutting surface, 12ga mild steel max (can be seen under power at our plant) $500 loading fee |
| 2003b | Located in Canon City, CO -- | Powermatic 20inch metal cutting band saw Model No. 87, disconnecting from power uninstalling and loading fee $500 |
| 2003c | Located in Canon City, CO -- | Plasma table CNC cutting system with Hypertherm Powermax 1000, computer system, approx 5' x 10' table capaple of cutting 1/2 steel, currently under power and in use, recently updated and upgraded. Removing from power and loading fee $500 |
| 2004 | Located in Canon City, CO -- | Dayton Drill Press MDL#32566 3/4hp 1/2" chuck, in operation $100 loading fee |
| 2005 | Located in Canon City, CO -- | Racking with approximately 300 Drive and coupling parts both new and used including pulleys, taperlocks, dodge coupling covers/grids/inputs, $100 loading fee, |
| 2006 | Located in Canon City, CO -- | TCM FHG 36NS, 8000lbs forklift with pneumatic tires, propane, 4' forks, 147" lift, SN 46400631, currently in use(can be seen under power at our plant), propane tank not included, Loading fee $100 |
| 2007 | Located in Canon City, CO -- | Delta drill press, missing chuck, runs, loading fee $50 |
| 2008 | Located in Canon City, CO -- | Dayton DC speed control loading fee $50 |
| 2009 | Located in Canon City, CO -- | Craftsman 10"table saw loading fee $50 |
| 2010 | Located in Canon City, CO -- | OTC Enforcer 100 100ton capacity horizontal hydrauclic press/puller used for dismantling gearboxes, portable on wheels, loading fee $50 |
| 2011 | Located in Canon City, CO -- | CPM pellet mill model PM7722-6, year 2008, SN 3A0625 with door and base, no motor but rated up to 300hp, for use with 22.5" die and rolls., recently running agricultural products, rated at 10-15 tons/hr on animal feed, loading fee $500 (approximate new cost $180,000) |
| 2012 | Located in Canon City, CO -- | Heavy Duty Rolling Table for steel, mounted on wheels, approximately 52"Wx115"Lx30-1/2"H, steel not included, loading fee $50 |
| 2013 | Located in Canon City, CO -- | Sprout Waldon (Andritz) Pellet Mill 26 disassembled for rebuilding, wtih 300hp motor, force feeder, conditioner, rated at approsimately 3 ton/hrs on wood pellets, and 3-5 tons/hr on alfafla (approximate new replacement cost $220,000) loading fee $500 |
| 2014 | Located in Canon City, CO -- | Atlas Copco GA55 Air compressor, $2500 Revomal, Rigging, and Loading |
| 2015 | Located in Canon City, CO -- | Air tank 8' long x 2'-6" round, $100 loading fee |
| 2016 | Located in Canon City, CO -- | Skip |
| 2017 | Located in Canon City, CO -- | RF12 and R13 insulation on a pallet $50 loading fee |
| 2018 | Located in Canon City, CO -- | Round screener approximately 40" stainless steel section, never used, no nameplate(similar to sweco/kason), 0.5hp, 1160rpm, 230/460v, $100 loading fee |
| 2019 | Located in Canon City, CO -- | Round Screener approximately 48" stainless steel section, never used, no nameplate,(similar to sweco/kason) 2.5hp, 1200rpm, 230/460v, $100 loading fee |
| 2020 | Located in Canon City, CO -- | Schutte hammer mill 38-13-300 150hp tear drop hammermill, last grinding peanut by products, rated at up to 50 tons/hr on corn (New replacement cost approximately $60,000) $500 loading fee |
| 2021 | Located in Canon City, CO -- | Jacobson 75hp 42311 hammer mill, rated up to 25 tons/hr on corn (New replacment cost $55,000)$500 loading fee |
| 2022 | Located in Canon City, CO -- | Buhler Feeder distributor model# DF AV1 w/2 transition pieces & 4 outlets, $50 loading fee |
| 2023 | Located in Canon City, CO -- | CPM CL3 SN 387513 pellet mill with stand and feeder, (new cost approximately $50,000), $100 loading fee |
| 2024 | Located in Canon City, CO -- | Champion Rotary Pocket Feeder Model 8x28 SN 808160 w/magnet (approximate new replacement cost $15,000)on 2 pallets loading fee $50 |
| 2025 | Located in Canon City, CO -- | Jacobson rotary pocket feeder with motor baffle inlet, w/magnets inlet 17x10 outlet 17x21 loadng fee $50 |
| 2026 | Located in Canon City, CO -- | Rotex 201 gearbox spins freely no backlash, SN R320774, for use with rotex 20 series machines, (new replacement cost approx $5,000) loading fee $50 |
| 2027 | Located in Canon City, CO -- | CPM cooler, Model 1B single stage vertical cooler SN 154499 upadated with new blador motor and cleveland gearbox, last running animal feed at 3 tons/hr, (New replacement cost approximately $20,000) loading fee $100 |
| 2028 | Located in Canon City, CO -- | Blower, no motor or belts, loading fee $50 |
| 2029 | Located in Canon City, CO -- | CPM DS2S empty gearbox sand blasted ready to for use, loading fee $50 |
| 2030 | Located in Canon City, CO -- | new/unused Meadow Grinding Mill steel burr mill, stainless hopper, for use with 5hp motor (new price approximately $4000) loading $100 |
| 2031 | Located in Canon City, CO -- | Lot: 3 CPM Pellet Mill Parts including mainshaft 3020, shear pin outer housing, pinion gear,(nrew replacement cost approximately $16,000) loading fee $50 |
| 2032 | Located in Canon City, CO -- | Sprout Andritz Mainshaft with nut for 26300 pellet mill.(new replacement cost approximately $20,000) loading fee $50 |
| 2033 | Located in Canon City, CO -- | Aftermarket pellet mill gearsfor CPM 7000, require polishing/rework loading fee $50 |
| 2034 | Located in Canon City, CO -- | Kice multi-Aspirator gravity cleaner, product separator, loading fee $50 |
| 2035 | Located in Canon City, CO -- | Del-tec air dryer Model PV-2PS, max pressure 150psi, loading fee $50 |
| 2036 | Located in Canon City, CO -- | CPM 3000 Misc parts including shear pin, quill flange, and mainshaft(new replacment cost approximately $20,000) loading fee $50 |
| 2037 | Located in Canon City, CO -- | Lot: Sprout 21 die housing and sprout deflector, (new replacement cost approximately $25,000)loading fee $50 |
| 2038 | Located in Canon City, CO -- | NEW Colorado Mill Equipment 30hp HMS XL with new 30hp Baldor motor 1 set of hammers, hopper, slide gate, safety switch, no stand, rated up to 10 tons/hr on corn (new repacement cost approximately $9000), loading fee $100 |
| 2039 | Located in Canon City, CO -- | Skip |
| 2040 | Located in Canon City, CO -- | Schutte 1380 hammer mill, with 150hp motor (new replacement cost approximately $50,000), loading fee $100 |
| 2041 | Located in Canon City, CO -- | Electric motor 100hp nameplate states 230/460V 405T frame 1775 Rpm, loading fee $50 |
| 2042 | Located in Canon City, CO -- | Marathon electric motor, tag hard to read believed to be 150hp 1800rpm |
| 2043 | Located in Canon City, CO -- | Teco westinghouse 100hp motor 230/460V 3560rpm 405TS loading fee $50 |
| 2044 | Located in Canon City, CO -- | Ideal Electric motor 75hp 1180 rpm 220/440 505 frame loading fee $50 |
| 2045 | Located in Canon City, CO -- | Leeson Ultimate E 100hp electric motor 405TS TEFC 3575 rpm, loading fee $50 |
| 2046 | Located in Canon City, CO -- | GE 200hp electric 1200rpm 460V 1190 rpm 449T loading fee $50 |
| 2047 | Located in Canon City, CO -- | US electric Motor 100hp 440V 445U 1800p rpm loading fee $50 |
| 2048 | Located in Canon City, CO -- | Baldor motor 150hp 460V 444T 1780 rpm loading fee $50 |
| 2049 | Located in Canon City, CO -- | Champion 3044 hammermill rotor, loading fee $50(has imbalance) |
| 2050 | Located in Canon City, CO -- | Lesson Ultimate E electric motor 100hp 3575 rpm 405TS loading fee $50 |
| 2051 | Located in Canon City, CO -- | Unused HMA30 hammermill 30hp with blower no motor loading fee $50(new replacement cost $50,000) |
| 2052 | Located in Canon City, CO -- | LOT: 5 CPM Century main/bull gears, taken from mills cleaned and prepped for future use on a rebuilt pellet mills, appear to be in good condition, no chips, (new replacement cost approximately $30,000-50,000) loading fee $50 |
| 2053 | Located in Canon City, CO -- | new rotor for champion 3044 hammermill purchased new for a hammermill rebuild project that was never completed, (new replacement cost approximately $12,000) loading fee of $50 |
| 2054 | Located in Canon City, CO -- | Circular screener, single ss deck, approximately 30" similar to sweco/kason. tested but never used, w/motor .5hp 230/460 loading fee $100 |
| 2055 | Located in Canon City, CO -- | Skip |
| 2056 | Located in Canon City, CO -- | Unused CME HMA30 hammermill with new 30hp motor and w/fan loading fee 100(new replacement cost $12,500) loading fee $500 |
| 2057 | Located in Canon City, CO -- | LOT: 2 new Buhler hammermills including: Grinder, rotor with hammers, and spare screens, hopper with slidegate, motor slide plate, no 5hp motor, Features: full circle grinding, belt drive design, 18 double sided heat treated hammers, rated at 1-2 tons/hr on corn depending on grind/crack size (new replacement cost approximately $5000) loading fee $50 |
| 2058 | Located in Canon City, CO -- | Sprout 21N-Ace Pellet mill SN 1993-0306, 21", not including 200hp motor, recently running alfalfa at approximately 3-4 tons/hr, running when taken out of service, (New replacement cost approx. $500,000-150,000) loading fee $500 |
| 2059 | Located in Canon City, CO -- | Lot: 2 new Lesson 7.5hp 1182rpm 254T electric motor 230/460V, loading fee $10 |
| 2060 | Located in Canon City, CO -- | Skip |
| 2061 | Located in Canon City, CO -- | Lot: (2) new sporut 21 wear rings and (2) new dies 1/4" x 2.25" effective for sprout 21 sprout pellet mill loading fee $50 |
| 2062 | Located in Canon City, CO -- | Sprout jr Model 500 pellet mill with feeder/conditioner recently running wood pellets, approx 50hp motor, running when taken of service, customer upgraded to larger machine, Ran wood pellets for 5 years (new replacement cost approximately $70,000-100,000)loading $500 |
| 2063 | Located in Canon City, CO -- | CPM stainless steel feeder with drive,(new replacement cost approximately $12,000) loading fee $50 |
| 2064 | Located in Canon City, CO -- | Skip |
| 2065 | Located in Canon City, CO -- | NEW CME Conditioner stainless steel shell approximately 10" x 5' with steam port, ss adjustable paddles, needs 1.5hp motor, (new price $6,500) $50 loading fee |
| 2066 | Located in Canon City, CO -- | New/unused Lesson ultimate E 50hp 3600rpm 230/460 326TS, $50 loading fee |
| 2067 | Located in Canon City, CO -- | Lesson 10hp, 230/460V 215TC, 3600rpm, $50 loading fee |
| 2068 | Located in Canon City, CO -- | Box of pulleys, 1 sprout 10 grove 501 pulley, misc 5 groove pullyes, taperlocks including new, used, and unused, etc loading fee $50 |
| 2069 | Located in Canon City, CO -- | NEW/Unused CME C5 top airlock no drive, (new cost $2900)loading fee $50 |
| 2070 | Located in Canon City, CO -- | USED CME 7" stainless steel auger no drive, (new cost $8,900)loading fee $50 |
| 2071 | Located in Canon City, CO -- | Lesson 30hp 3600 rpm 286TSC 230/460, loading fee $50 |
| 2072 | Located in Canon City, CO -- | Unused WNM 10hp 256T 230/460V 1785 RPM, loading fee $50 |
| 2073 | Located in Canon City, CO -- | Lot of 2 techtop, 1 baldor and 40 to 1 gearbox made by clevelandgear, loading fee $50 |
| 2074 | Located in Canon City, CO -- | Lot of 2 NEW unused CME 9" stainless steel feeder no drive, (new price $9500 each) loading fee $50 |
| 2075 | Located in Canon City, CO -- | NEW Baldor 30hp 3600rpm 256TSC 460V, loading fee $50 |
| 2076 | Located in Canon City, CO -- | NEW Techtop 25hp 3600 rpm 230/460V 284TSC, loading fee $50 |
| 2077 | Located in Canon City, CO -- | New/unused Techtop motors 1 is 3hp 3600rpm 230/460V, 2nd is 25hp 3600rpm, 230/ 460V, $50 loading fee |
| 2078 | Located in Canon City, CO -- | New/Unused 15hp Techtop 1200 rpm 284T , loading fee $50 |
| 2079 | Located in Canon City, CO -- | New/unused 40hp motor, 324TSC 3600rpm 230/460V, loading fee $50 |
| 2080 | Located in Canon City, CO -- | LOT: CME conditioner, force feeder, feed chute, guards, no motors, (new cost $20,000) loading fee $50 |
| 2081 | Located in Canon City, CO -- | LOT: 3 new/unused R30 conditioners, 10" x 5' stainless stee, adjustable paddle, (new cost $6500 each) loading fee $50 |
| 2082 | Located in Canon City, CO -- | SKIP |
| 3083 | Located in Canon City, CO -- | skip |
| 2084 | Located in Canon City, CO -- | NEW CME R30 stainless conditoner, with 2hp motor, (new remplacement cost $6900) $50 loading fee |
| 2085 | Located in Canon City, CO -- | R30 stainless Conditioner, No Motor with guards(new cost $6500) $50 loading fee |
| 2086 | Located in Canon City, CO -- | skip |
| 2087 | Located in Canon City, CO -- | CPM 202 SN 2020-294059 empty pellet mill with mainshaft, quill, and box of additional parts, no motor loading fee $100 |
| 2088 | Located in Canon City, CO -- | skip |
| 2089 | Located in Canon City, CO -- | skip |
| 2090 | Located in Canon City, CO -- | CPM 7000 empty gearbox with base and crate of parts, loading fee $500 |
| 2091 | Located in Canon City, CO -- | skip |
| 2092 | Located in Canon City, CO -- | skip |
| 2093 | Located in Canon City, CO -- | Lot: CPM 7000 Baseplate, stainelss door with dump chute and 7000 1/4" die, loading fee $100 |
| 2094 | Located in Canon City, CO -- | Sprout 500B Pellet jr mill with feeder/conditioner, missing belts and feed chute, includes approximately 3/16 die and rolls with feedcone, last running in a university, (new replacement cost approx. $75,000-100,000) loading fee $500 |
| 2095 | Located in Canon City, CO -- | CME R30 stainless condtioner no motor, (new nost $6500) $50 loading fee |
| 2096 | Located in Canon City, CO -- | Lot: discontinued new stainless gravity feed chutes and force feeder augers, (new cost $15,000) loading fee $50 |
| 2097 | Located in Canon City, CO -- | LOT: 2 discontinued force feeders and R30 conditioner (new cost $11,500)loading fee $50 |
| 2098 | Located in Canon City, CO -- | LOT: 2 stainless screw feeder shells with gearbox, loading fee $50 |
| 2099 | Located in Canon City, CO -- | Sterling 200hp 449TZ 460V 1185rpm eelctive motor, loading fee $500 |
| 2100 | Located in Canon City, CO -- | LOT: 3 gravity bag scales: JEM/ESP type,(new cost approximately $3000 each) loading fee $100 |
| 2101 | Located in Canon City, CO -- | CME 9" stainless steel auger, loading fee $50 |
| 2102 | Located in Canon City, CO -- | Electric motor, reported as 150hp no nameplate to confirm, includes 14 groove pulley, $500 loading fee |
| 2103 | Located in Canon City, CO -- | Baldor 100hp 1180 rpm 460V 444T loading fee $500 |
| 2104 | Located in Canon City, CO -- | GE 50hp 3560 rpm 550V 365U, Loading fee $50 |
| 2105 | Located in Canon City, CO -- | Candian GE 100hp 1180 rpm 575V 444T loading fee $100 |
| 2106 | Located in Canon City, CO -- | Pacemaker electric motor 125HP 1200rpm 460V 444T loading fee $100 |
| 2107 | Located in Canon City, CO -- | Reliance electric motor 300hp 1785 rpm 460V 449TS loading fee $100 |
| 2108 | Located in Canon City, CO -- | Westinghouse 150hp 575V 447T 1185rpm loading fee $500 |
| 2109 | Located in Canon City, CO -- | Louis Allis 150hp 447US 230/460V 1780RPM loading fee $100 |
| 2110 | Located in Canon City, CO -- | Electric Motor approximately 100 1800rpm? loading fee $500 |
| 2111 | Located in Canon City, CO -- | Baldor 100hp electric motor 405T 230/460V 1760rpm loading fee $100 |
| 2112 | Located in Canon City, CO -- | Allis Chalmers 75hp, loading fee $500, 1170rpm 505 220/440 |
| 2113 | Located in Canon City, CO -- | Techotop 150hp, 460V 1180rpm 447T, loading fee $100 |
| 2114 | Located in Canon City, CO -- | Reliance 75hp, 445U, 1190rpm, 220/440 loading fee with $500 |
| 2115 | Located in Canon City, CO -- | Clark CHY160B Forklift, SN HY1425-13-1147, Clark states that the lift is rated at 16k lbs but nameplate says 10,500 at 48", outdoor tire, pneumatic, 686 hours, propane, 8ft forks, super heavy duty forklift, runs,(propane tank not included) loading fee $500 |
| 2116 | Located in Canon City, CO -- | CPM 7000 broken quill with bearings, wear ring, and locking key/block, (not originally 2pc)loading fee $50 |
| 2117 | Located in Canon City, CO -- | Large conditioner Sprout 30x144. stainless steel adjustable paddles, with 25 motor, needs belts,(new replacement cost approximately $40,000) Last runnign with PM919 pellet mill $500 loading fee |
| 2118 | Located in Canon City, CO -- | Williams Hammer Mill C32 Pulverizer Crusher, 100hp,. 22lbs swinging hammers, removable air damn, extreme dutry bearings, metal kickout chamber, 1" wear plates, Age approx 2001 (new replacement cost approximately $50,000) loading fee $500 |
| 2119 | Located in Canon City, CO -- | LOT: Pallet of new/unused motor, many in factory crate, (8) motors (3) 7.5hp (2)1.5hp (2)5hp (1)1hp, loading fee $100 |
| 2120 | Located in Canon City, CO -- | LOT:9 motors (3)NEW 1.5hp Echotop (1) NEW 1hp Techotop (2)3hp Baldor (1)3hp Brook Crompton (1)5hp Indusrtial Electric (1)2hp North American Electric $500 loading Fee |
| 2121a | Located in Canon City, CO -- | LOT: 21 Eura drives: ac drives mostly 220V, single and 3phase |
| 2121B | Located in Canon City, CO -- | LOT: (4) 380. Chaoyi (4) QX1-13 380v switch |
| | Located in Canon City, CO -- | GS ac drives model#GS2-23P0 230V 3hp. |
| 2122 | Located in Canon City, CO -- | LOT: 8 NEW and USED motors (1)North American 1.5hp (1) Bad (1)? (1)WNM1.5hp (1)WNM 3hp (2)WNM 2hp (1)Brooks Champion 10hp , $100 loading fee |
| 2123 | Located in Canon City, CO -- | LOT: 10 NEW Baldor motors (5) 1hp (2)3hp (3)1.5hp |
| 2124 | Located in Canon City, CO -- | Ajax 100hp 1185 rpm 444T 230/460V $100 loading fee |
| 2125 | Located in Canon City, CO -- | Heavy duty steel swivel mounting plate stand, qty 4, new price $390 each) loading fee $50 |
| 2126 | Located in Canon City, CO -- | Heavy duty steel swivel mounting plate stand, qty 2, new price $390 each) loading fee $50 |
| 2127 | Located in Canon City, CO -- | LOT: 4 NEW MOTORS (3)Techotop 3hp (1)North American Electric 15hp |
| 2128 | Located in Canon City, CO -- | CME R30 conditioner stainless steel paddle and tube qty 2 (new price $6500 each) loading fee $100 |
| 2129 | Located in Canon City, CO -- | NEW (3)Techotop 7.5hp 1200 230/460V 254T Loading fee 100 |
| 2130 | Located in Canon City, CO -- | NEW North American 20hp 3600rpm motor 256T, loading fee $100 |
| 2131 | Located in Canon City, CO -- | NEW (3)Techotop 7.5hp (7) motor front plates (3)15hp (2)3hp (1)25hp (1)20hp fee $100 |
| 2132 | Located in Canon City, CO -- | Lincoln Electric motor 150hp 460V 1180rpm, loading fee $100 |
| 2133 | Located in Canon City, CO -- | Lot: 3 stainless steel feeders 1 new(new cost $9000), 2 used/parts, loading fee $100 |
| 2134 | Located in Canon City, CO -- | SKIP |
| 2135 | Located in Canon City, CO -- | New swivel stand (new cost $390), load out $50 |
| 2136 | Located in Canon City, CO -- | Conditioner belt guard, load out fee $50 |
| 2137 | Located in Canon City, CO -- | pallet of ss feeder shell, force feder, 2 gearbox drives, and 2 motors, load out fee $50 |
| 2138 | Located in Canon City, CO -- | LOT: 2 NEW/Unused motors, North American Electric 10hp 1175rpm load out fee $100 |
| 2139 | Located in Canon City, CO -- | New CME feeder, no motor / gearbox, load out fee $50 |
| 2140 | Located in Canon City, CO -- | LOT: 6 main/bull gears last running in CPM century / 7000 etc pellet mills saved for use future rebuilds, (new replacement cost approximately $30,000)loading fee $100 |
| 2141 | Located in Canon City, CO -- | LOT: Misc CPM other parts including , scrapers, CPM rebuilt rolls, feed cone, roll shipping bases, coupling parts loading fee $100 |
| 2142a | Located in Canon City, CO -- | Seraph industries pellet stove for wood or corn, load out fee $100 |
| 2142b | Located in Canon City, CO -- | Pallet of approx 20-30 bags Hearthwood hardwood pellets wood pellets loadout fee $50 |
| 2143 | Located in Canon City, CO -- | LOT: 3 eyewash stations, load out fee $50 |
| 2144 | Located in Canon City, CO -- | Northstar weed sprayer, laod out fee $50 |
| 2145 | Located in Canon City, CO -- | DeWalt Pressure Washer 8hp engine load out fee $50 |
| 2146 | Located in Canon City, CO -- | Lot: 3 largre rolls of stainless steel mesh, 48" wide (1)1/4 (1)3/16 (1) 1/16,, loading fee $50 |
| 2147 | Located in Canon City, CO -- | Lot: 6 NEW Rolls of approx 48" wide 5/8" squares rebounding ball wire for rebuilding rotex screeners, (new cost over $500 per roll) Loading fee $100 |
| 2148 | Located in Canon City, CO -- | Lot: Approx 26 Partially used rolls of assorted ss mesh various sizes, (5) 5/8 (2)4mm (1)2mesh (1)10mesh (3)8mesh (1)5mm (1)6mesh (2)12mesh (2)20mesh (3)30mesh (4)6mm (1)12mm (new cost approximately $400 per roll) loading fee $50 |
| 2149 | Located in Canon City, CO -- | Lot: Food Grade Grease approx 200 tubes, JAX Magnaplate 44-1, (new cost approximately $1200) loading fee $50 |
| 2150 | Located in Canon City, CO -- | skip |
| 2151 | Located in Canon City, CO -- | New/unused stainless feed chute for CPM 7000, (new cost approximately $3900) laoding fee $100 |
| 2152 | Located in Canon City, CO -- | Sprout Andritz pellet mill Model 26W300 SN 761213 with a WEG 250hp 1200rpm motor recently last running wood alfalfa pellets, door removed for shipping purposes, includes 1/4" die and rolls, and force feeder.(new replacement cost approximately $200,000) loading fee $500. |
| 2153 | Located in Canon City, CO -- | Lot 2 rolls for CPM 7000 pellet mill, loading fee $50 |
| 2154 | Located in Canon City, CO -- | NEW R30 feeder / conditioner, (new price 9000)loading fee $50 |
| 2155 | Located in Canon City, CO -- | CPM DS Series Gearbox, requires shear pin, door, feed cone etc, loading fee $100 |
| 2156 | Located in Canon City, CO -- | NEW WNM 30hp motor 230/460V 3550rpm 286TS loading fee $100 |
| 2157 | Located in Canon City, CO -- | CPM 7800 gearbox with quill, main gear, pinion gear, and covers 30inch die, missing door and mainshaft etc loading fee $100 |
| 2158 | Located in Canon City, CO -- | Sprout 26 pellet mill Model 26NW300 SN80591with force feeder, good gears last running wood pellet at approximately 3 tons/hr, loading fee $500 |
| 2159 | Located in Canon City, CO -- | Sprout Andritz pellet mill model 26 series, last running in line running wood pellets, includes feeder/conditioner, force feeder, good gears, upgraded heaby duty die housing, shear pin upgraded to brake assembly, no motors (new replacment cost approximately $250,000) loading fee $500 |
| 2160 | Located in Canon City, CO -- | CPM conditioner approximately 18" x 6/5', w/motor 20hp motor,. stainless steel adjustable paddles, with die hoist(new replacment cost approximately $30,000) loading fee $100 |
| 2161 | Located in Canon City, CO -- | LOT: 2 Sprout 501 die housings, no cracks, (new replacment cost $9,000 each)loading fee $100 |
| 2162 | Located in Canon City, CO -- | skip |
| 2163 | Located in Canon City, CO -- | Sprout 26 pellet mill with feeder conditioner, and force feeder, no motor, dies shown on base not included, good gears(new replacement cost approximately $250,000) loading fee $500 |
| 2164 | Located in Canon City, CO -- | LOT: 3 Used 7000 Dies 22 1/2" x 1/4" holes,Last running animal feed (new replacement cost $5500 each) loading fee $100 |
| 2165 | Located in Canon City, CO -- | Sprout Andritz Feeder Conditioner for Sprout 26" mill, no motor, (new replacement cost approximately $30,000) Loading fee $100 |
| 2166 | Located in Canon City, CO -- | Sprout Andritz Feeder Conditioner for Sprout 26" mill, no motor, (new replacement cost approximately $30,000) Loading fee $100 |
| 2167 | Located in Canon City, CO -- | Lot: 2 US General US660V Air Compressor 3.5hp 12.35 acfm at 100psi 15amps 60 gallon(new price approximtely $750 each)Loadign fee $100 |
| 2168 | Located in Canon City, CO -- | CPM 7800 Main Shaft with outer shearpin housing and misc parts(new replacement cost approximately $20,000) laoding fee $100 |
| 2169 | Located in Canon City, CO -- | Sprout Waldron Andritz vertical cooler rated at approximately 6-8 tons/hr of cooling, last running animal feed,(new replacment cost approximately $20,000) loading fee $100 |
| 2170 | Located in Canon City, CO -- | Brook Crompton 300hp 449TZ, 1190 rpm 460V, Loading fee of $100 |
| 2171 | Located in Canon City, CO -- | Sprout vertical pellet cooler model 375 rated at approximately 6-8 tons/hr, missing drive motor, sepatared into 2 pcs for shipping purposes |
| 2172 | Located in Canon City, CO -- | LOT 2 sprout stiffener rings and 2 feed cones for sprout 26 gearbox pellet mills, (total new replacment cost approxiamtely $10,000) loading fee $100 |
| 2173 | Located in Canon City, CO -- | LOT: Misc parts for Sprout 26 pellet mills including: scrapers, roll shafts, roll shells, loading fee $50 |
| 2174 | Located in Canon City, CO -- | LOT: 2 Sprout 501 Narrow roll assemblies with new shells (new replacement cost approximately $1200 each)loading fee $50 |
| 2175 | Located in Canon City, CO -- | LOT: Misc parts for Sprout 26 pellet mills including: scrapers, roll shafts, roll shells, loading fee $50 |
| 2176 | Located in Canon City, CO -- | Lot: 2 Sprout 26 Rolls with shells in excellent condition(new cost approximately $1300 each) loading fee $50 |
| 2177 | Located in Canon City, CO -- | Lot: 2 Sprout 501 rolls narrow, minimal wear, (new cost approximately $1200 each) loading fee $50 |
| 2178 | Located in Canon City, CO -- | Lot: 2 Sprout 501 dies, 1/4 hoes approximately 2" thick. last running animal feed, loading fee $50 |
| 2179 | Located in Canon City, CO -- | LOT 2: Timken Pillow Block Bearing Housing SAF520 loading fee $50 |
| 2180 | Located in Canon City, CO -- | Sprout 501 Cartridge with 14 groove pulley, Main Shaft and die housing and die (new cost approximately $20,000) Loading fee $100 |
| 2181 | Located in Canon City, CO -- | skip |
| 2182 | Located in Canon City, CO -- | skip |
| 2183 | Located in Canon City, CO -- | skip |
| 2184 | Located in Canon City, CO -- | skip |
| 2185 | Located in Canon City, CO -- | skip |
| 2186 | Located in Canon City, CO -- | skip |
| 2187 | Located in Canon City, CO -- | skip |
| 2188 | Located in Canon City, CO -- | skip |
| 2189 | Located in Canon City, CO -- | NEW CPM Hyflow l CPM 1012 Wide die, new never used 1/4" x 2" Exp, (new cost approximately $2900) loading fee $50 |
| 2190 | Located in Canon City, CO -- | Lot: 5 Sprout 501 feed cone, 4 501 siffener rings, and various lab seals, bearings, fasteners, (new replacement cost approximately $50,000) loading fee $50 |
| 2191 | Located in Canon City, CO -- | Lot: 7 sprout 501 narrow rolls with good or new shells, (approximate new replacment cost $8,000-12,000. loading fee $50 |
| 2192 | Located in Canon City, CO -- | Used CPM Century die 16" diameter 1/4 hole, (new replacement cost approximately $3500) loading fee $50 |
| 2193 | Located in Canon City, CO -- | Cartridge Housing for CPM 22" mill (new replacement cost approximately $50,000) loading fee $50 |
| 2194 | Located in Canon City, CO -- | LOT: CPM stainless pellet mill century door, 262 gear reducer wtih motor (replacment cost approximately $5000) loading fee $50 |
| 2195 | Located in Canon City, CO -- | CPM Door double hinged last running on 16" CPM Pellet Mill, with vents knife post, and handles (new cost approximately $5000) loading fee $50 |
| 2196 | Located in Canon City, CO -- | skip |
| 2197 | Located in Canon City, CO -- | Lot: Express Scale JMDT2502 SN020362, with foot switch, digital readout, loading fee $100 |
| 2198 | Located in Canon City, CO -- | General Electric Motor 300hp, 449T 1800 460V, loading fee $100 |
| 2199 | Located in Canon City, CO -- | Sprout Die 26"narrow -1/4 holes approx 2" thick, loading fee $50 |
| 2200 | Located in Canon City, CO -- | CPM Door approximately 50" diameter with feed chute for 7800 or similar pellet mill, loading fee $100 |
| 2201 | Located in Canon City, CO -- | Sprout feeder 1.5hp and conditioner w/motor10hp last running with 26" pellet mill, last running animal feed,(new replacement cost approximately $30,000) loading fee $100 |
| 2202 | Located in Canon City, CO -- | LOT: Sprout 501 1/4" die with 3 rebuilt 501 roll assemblied, loading fee $50 |
| 2203 | Located in Canon City, CO -- | Lot: Lesson 3hp motor and Dayton 1/2hp reducer, loadinge fee $50 |
| 2204 | Located in Canon City, CO -- | Used CPM Conditioner 18" x 5', loading fee $50 |
| 2205 | Located in Canon City, CO -- | Western Electric motor 100hp 1800rpm 230/460V loading fee 100 |
| 2206 | Located in Canon City, CO -- | Hyster Forklift H80C Propane, newer tires 8000 capacity pneumatic tire, can inspect running at our facility, (no propane tank) loading fee $100 |
| 2207 | Located in Canon City, CO -- | CPM Feeder and Conditioner w/1hp Baldor motor, loading fee $100 |
| 2208 | Located in Canon City, CO -- | Buhler stainless steel conditioner, 42" x 9', Loading fee $100 |
| 2209 | Located in Canon City, CO -- | RARE CPM flat die pellet mill, one of CPM's first pellet mill designs before they made ring die machines, made in San Francisco CA, loading fee $100 |
| 2210 | Located in Canon City, CO -- | Westinghouse 200hp motor 1800rpm 460 447TS with partial coupling, loading fee $100 |
| 2211 | Located in Canon City, CO -- | Sprout pellet cooler model 375 or similar,(approximate new replacement cost $20,000) loading fee $100 |
| 2212 | Located in Canon City, CO -- | CPM small cooler with crumbler, (approximat new replacement cost approximately $30,000)loadng fee $100 |
| 2213 | Located in Canon City, CO -- | CPM feeder 7'x10" with motor loading fee $50 |
| 2214 | Located in Canon City, CO -- | CPM Feeder 5'x 12", stainless shell, mild steel screw with motor/reducer loading fee $50 |
| 2215 | Located in Canon City, CO -- | Westinghouse 100hp, 1800 rpm motor 445US 220/440 loading fee $100 |
| 2216 | Located in Canon City, CO -- | CPM Cooler 3'x3', parts machine, appears to model 2GA, loading fee $50 |
| 2217 | Located in Canon City, CO -- | Stainless Conditioner, approximately 18" x66" no motor, adjustable paddles loading fee $50 |
| 2218 | Located in Canon City, CO -- | Towmotor forklift, propane 12,000 rated but has lifted more, currently running and in use, (no propane tank) loading fee $100 |
| 2219 | Located in Canon City, CO -- | 5 ton Wallace Gantry model:5T19-20 12'-6 1/2" tall x 7'-9"wide with hoist, loading fee $500 |
| 2220 | Located in Canon City, CO -- | CPM 7000 pellet mill in process of being rebuilt(replacement cost approximately $260,000) loading fee $500 |
| 2221 | Located in Canon City, CO -- | Buhler 400hp pellet mill disassemble for rebuild (replacement cost approximately $275,000) loading fee $500 |
| 2222 | Located in Canon City, CO -- | Sprout 26 LM2 pellet mill disassembled for rebuild (replacement cost approximately $275,000) loading fee $500 |
| 2223 | Located in Canon City, CO -- | Colorado Mill Equipment HMX400 44x40 hammermill with 200hp motor, made in 2017, low hours, updated door locks, rated up to 400hp loading(New replacement cost $70,000)fee $500 |
| 2224 | Located in Canon City, CO -- | Torin Big Red Jacks 40 ton pneumatic shop press, runs/currently in use loading fee $100 |
| 2225 | Located in Canon City, CO -- | Mitsubishi 4000lbs forklift model FGC20, propane, in use / running, (no propane tank) loading fee $500 |
| 2226 | Located in Canon City, CO -- | Clark 8k lbs forklift, propane, 8' forks, pneumatic tires, currently in use/runs, (propane tank not included) loading fee $500 |
| 2227 | Located in Canon City, CO -- | Hyster50 forklift propane, cushion tires, triple mast with 185.5" lift, 3350lb at 25.5" max load, weak brakes, runs,(no propane tank) loading fee $500 |
| 2228 | Located in Canon City, CO -- | Binks Air Paint Cabinet, removal and loading fee $500 |
| 2229 | Located in Canon City, CO -- | Yard Sport YS200 4X2, a lot of fun, but wont start right now, loading fee $100 |
| 2230 | Located in Canon City, CO -- | Dynamic Balancing Machine, Dynamics Research, Noremac 605, Rated up to 5000lbs Over 60" swing and length, with 10hp motor, rebuilt and completely updated with Easy Balance Controls. New Replacement cost approximately $75,000 |
| 2231 | Located in Canon City, CO -- | CME 2019 10hp Stainless Steel HMS w/Base, very low hours only used in lab (new cost $16,000) loading fee $500 |
| 2232 | Located in Canon City, CO -- | CME Mill 10 Pellet Mill with 10hp motor, die and rolls new cost $7000, only used in lab, very low hours, loading fee $100 |
| 2233 | Located in Canon City, CO -- | CME R30 Pellet Mill, very low hours only used in lab, with ss door, die, rolls, special infeed chute, new cost $25,000, removal and loading fee $500 |
| 2234 | Located in Canon City, CO -- | CME RB500 Ribbon Blender only ran in lab, new cost approx $7000, Loading fee $500 |
| 2235 | Located in Canon City, CO -- | Faro Arm CMM model:P08 revision 21.4 serialnumber: P08-02-05-03683 Loading fee $50 |
| 2236 | Located in Canon City, CO -- |
Bliss 150hp pellet mill with dual motor, last running alfalfa pellets in April 2020, replaced with higher production machine, with spare parts, reported in running condition, Loading Fee $500 |
| 3000 | Located in Canon City, CO -- | Hankook lathe Model: HPL, SN PB9N05-07, 4 Jaw 31.5" Chuck, 35.4" Swing, 157" distance between centers, Spindle RPM 14-1120, Cross Feed: .0023-.012 IPR, Apron feed .0047-.027 IPR MFG Date 5/29/89 20hp 480v, currently under power and running, (approx new replacement cost 100k) loading fee $500 |
| 3001 | Located in Canon City, CO -- | MSC Band Saw 7X12 1hp 110v, 3/4 x .032" x 93" blade, SN 372536, built 2003, in use and under power, loading fee $100 |
| 3002 | Located in Canon City, CO -- | Takisawa Lathe Lathe Model: 1000CD Serial Number: T89090051 Date of Manufacture: 1989 Spindle RPM: 55-1800 Feed: .0015-.0826 IPR Accessories: Tailstock, Steady Rest, Quick Change Tool Post, Anilam MiniWizard Direct Read Out Power: 240 Volts, currently in use and under power, loading fee $100 |
| 3003 | Located in Canon City, CO -- | Vantage End Mill Vertical Knee Mill 3HP Make: Jih Fong Machinery with a Vantage Head, the head has been replaced at some point Model: JF-153V Serial Number: 95190 X Axis Travel: 30" Y Axis Travel: 11.5" Accessories: X Axis Power Feed, Delos Direct Read Out, 11 R8 Collets. VISE SHOWN NOT INCLUDED. load out fee $100 |
| 3004 | Located in Canon City, CO -- | Clark Fork Lift propane 12,000# cap 3'-1/2" forks "NOT RUNNING, had problems with engine loadout fee $100 |
| 3005 | Located in Canon City, CO -- | Hyster S35XM SN D010H02294Z 3400lbs forklift solid tires, propane, currently in use, double mast with fork positioner, load out fee $100 |
| 3006 | Located in Canon City, CO -- | Hyster 141H forklift, electric, believed to need new battery, currently not operational, load out fee $100 |
| 3007 | Located in Canon City, CO -- | Hobart Charger Model#1R18-550, electric charger for forklift, 36v output 115amps ,load out fee $50 |
| 3008 | Located in Canon City, CO -- | Ramco Patriot End Mill Delta 10 CNC Ram8 220v, not currently in service, SN 8906400143 Axis CNC Mill, BT 40 Taper, 13" X 42" Table, Spindle Drive Error and Fault, Ball Screw Bearing Housing Failure. load out fee $100 |
| 3009 | Located in Canon City, CO -- | Hobart Charger Model#1R18-550, electric charger for forklift, 36v output 115amps ,load out fee $50 |
| 3010 | Located in Canon City, CO -- | TB Lathe C3123 Binns and Berry 12.5 TB MK 1, swing is 24" and swing in gap is 44", running when taken out of service and replaced with larger unit, load out fee $500 |
| 3011 | Located in Canon City, CO -- | LOT: Sprout 501 door with main pulley cover and seal plates, misc guards, load out fee $100 |
| 3012 | Located in Canon City, CO -- | Lot: Misc gaurds, cables conduit, etc, loadout fee $50 |
| 3013 | Located in Canon City, CO -- | CPM pellet mill 1116-4 SN 399427 Year 1999, w/Toshiba-Houston 100hp 230/460v motor with double knife door, stainless gravity dump chute, stand, complete with die, rolls, front, feed cone, and die clamps (New replacement cost approximately $120,000) load out fee $500 |
| 3013B | Located in Canon City, CO -- | LOT: 14 assorted 501 narrow dies with various holes sizes and effectives,for use with stiffener ring load out fee $100 |
| 3014 | Located in Canon City, CO -- | Sprout 501HL base, 14 groove main pulley(has chip on outside) and mainshaft, Sprout main pulley shroud load out fee $100 |
| 3015 | Located in Canon City, CO -- | Lot: Misc gaurds, cables conduit, etc, loadout fee $50 |
| 3017 | Located in Canon City, CO -- | CPM century/roughager gearbox SN 237004 empty gearbox load out fee $100 |
| 3018 | Located in Canon City, CO -- | CPM 125C empty gearbox, loading fee $100 |
| 3019 | Located in Canon City, CO -- | LOT: CPM Main Shafts and 1 rolls assembly, load out fee $100 |
| 3020 | Located in Canon City, CO -- | SKIP |
| 3021 | Located in Canon City, CO -- | CPM die clamps Load out fee $50 |
| 3022 | Located in Canon City, CO -- | Sprout feeder conditioner shaft load out fee $50 |
| 3023 | Located in Canon City, CO -- | Sprout stainless feeder / conditioner(new replacement cost approximately $20,000) load out fee $100 |
| 3024 | Located in Canon City, CO -- | Abar Ipsen HR26x36 vacuum heat treating oven with ancillary pumps and controls recently running at a parker hannifin location in 2019, 24" wide x 18" high x 36" deep work zone, 16" varian pump, stokes 212 roughing pump, 412 booster pump, updated controls, fully supported by mfg(new replacement approx $500,000-600,000) Load out fee $500 |
| 3025 | Located in Canon City, CO -- | skip |
| 3026 | Located in Canon City, CO -- | Towmotor Cat Forklift Model#750SG15024 propane, 15k forklift, can be inspected under power at facility, currently in use, 8' forks, loading fee $500 |
| 3027 | Located in Canon City, CO -- | Grieve Ovens Industrial Oven Model#AB-850 460v 32.5amps 24KW, Max chamber temp 850F 24" x 24" x 24" inside chamber, modern unit still built built today by Greive, (new replacement cost approximately $20,000) load out fee $100 |
| 3028 | Located in Canon City, CO -- | Baldor 2hp motor with Reeves drive load out fee $50 |
| 3029 | Located in Canon City, CO -- | Daewoo GC25s Forklift propane, outdoor solid tires triple mast 188 total lift, 4000lbs, currently runs, to see under power you can see at facility, controls for up/down, tilt, shift, load out fee $100 |
| 3030 | Located in Canon City, CO -- | LOT: Spare dies and Rolls for Mill30 30hp flat die pellet mill, also pulleys, roll adjuster, guards etc, load out fee $50 |
| 3031 | Located in Canon City, CO -- | Lot: 2 Sprout 21N250 pellet mill die housings and 1 stiffener ring ( new replacement cost approximately $30,000) load out fee $100 |
| 3032 | Located in Canon City, CO -- | Lot:Misc. Sprout spare parts including 4 501 roll assemblies, front plate, feed cone, gearbox, shear pins, etc. Load out fee $50 |
| 3033 | Located in Canon City, CO -- | Lot: 2 501 sprout dies with stiffener rings and 2 Roll assmblies, top pallet only load out fee $100 |
| 3034 | Located in Canon City, CO -- | Lot: 2 Sprout Andritz 501 mainshafts(new replacment cost approximately $10,000 each) and 3 feed cones for sporut 501 Loading fee $100 |
| 3035 | Located in Canon City, CO -- | Lot: Misc Hammermill screens, load out fee $50 |
| 3036 | Located in Canon City, CO -- | Lot: sprout Jr 500 die 11/64 x 1.5" effective approx, 1 1/2 overall thickness, 2 gravity feed chutes, and ss seal ring, load out fee $50 |
| 3037 | Located in Canon City, CO -- | Lot: Misc. Parts, electrical etc loading fee $50 |
| 3038 | Located in Canon City, CO -- | New/Unused C3 screener with discharge gate and spring loaded from support bracket, primed only, no vibratory motor, no stand, rated at up to 1-5 tons/hr(new replacement cost $5000) load out fee $50 |
| 3039 | Located in Canon City, CO -- | New/Unused C3 screener with discharge gate and spring loaded from support bracket, primed only, no vibratory motor, no stand, rated at up to 1-5 tons/hr(new replacement cost $5000) load out fee $50 |
| 3040A | Located in Canon City, CO -- | New C10 blower housing, no motor, no shaft, load out fee $50 |
| 3040B | Located in Canon City, CO -- | New CME HMA30 hammermill with 30hp and blower (NEW COST $12,500) load out fee $100 |
| 3041 | Located in Canon City, CO -- | Anver lifting system systems vacuum suction cup lifting unit, loading fee $100 |
| 3042 | Located in Canon City, CO -- | skip |
| 3043 | Located in Canon City, CO -- | New/Unused C3 screener with discharge gate and spring loaded from support bracket, primed only, no vibratory motor, no stand, rated at up to 1-5 tons/hr(new replacement cost $5000) load out fee $50 |
| 3044 | Located in Canon City, CO -- | New/Unused C3 screener with discharge gate and spring loaded from support bracket, primed only, no vibratory motor, no stand, rated at up to 1-5 tons/hr(new replacement cost $5000) load out fee $50 |
| 3045 | Located in Canon City, CO -- | New/Unused C3 screener with discharge gate and spring loaded from support bracket, primed only, no vibratory motor, no stand, rated at up to 1-5 tons/hr(new replacement cost $5000) load out fee $50 |
| 3046 | Located in Canon City, CO -- | skip |
| 3047 | Located in Canon City, CO -- | skip |
| 3048 | Located in Canon City, CO -- | 30KVA Transformer 3phase 480V, load out fee $50 |
| 3049 | Located in Canon City, CO -- | Lot: Misc CPM parts including die clamps, century feed cone, outer shear pin, die clamp, top cover loading fee $50 |
| 3050 | Located in Canon City, CO -- | Miller Gas Powered Welder Roughneck 2E, load out fee $50 |
| 3051 | Located in Canon City, CO -- | NEW unused CME 5" x 8 auger, missing motor pulley load out fee $50 |
| 3053 | Located in Canon City, CO -- | skip |
| 3052a | Located in Canon City, CO -- | skip |
| 3052 | Located in Canon City, CO -- | Lot: Misc 1-2hp Cylcoidal Gear Reducers, load out fee (replacement cost approximately $300 each) $50 |
| 3054 | Located in Canon City, CO -- | skip |
| 3055 | Located in Canon City, CO -- | skip |
| 3056 | Located in Canon City, CO -- | skip |
| 3057 | Located in Canon City, CO -- | skip |
| 3058 | Located in Canon City, CO -- | skip |
| 3059 | Located in Canon City, CO -- | skip |
| 3060 | Located in Canon City, CO -- | skip |
| 3061 | Located in Canon City, CO -- | skip |
| 3062 | Located in Canon City, CO -- | skip |
| 3063 | Located in Canon City, CO -- | skip |
| 3064 | Located in Canon City, CO -- | skip |
| 3065 | Located in Canon City, CO -- | skip |
| 3066 | Located in Canon City, CO -- | skip |
| 3067 | Located in Canon City, CO -- | skip |
| 3068 | Located in Canon City, CO -- | skip |
| 3069 | Located in Canon City, CO -- | skip |
| 3070 | Located in Canon City, CO -- | skip |
| 3071 | Located in Canon City, CO -- | Sprout 26NW300 pellet mill with250hp motor(but motor is not mounted on machine, includes door, force feeder, last runing wood pellets at 3 tons/hr, rated at 3-5 tons/hr on alfalfa, and up to 12 tons/hr on general feeds, (replacement cost approximately $200,000) load out fee $500 |
| 3072 | Located in Canon City, CO -- | CPM Master 30hp pellet mill with feeder and conditioner, rate at approximately 1 ton/hr on general feeds replacment cost new approximately $75,000 loading fee $100 |
| 3073 | Located in Canon City, CO -- | skip |
| 3074 | Located in Canon City, CO -- | LOT: Misc CPM parts including century shear pin housings, feed cones, plates, pellet mill die, valves etc loadout fee $50 |
| 3075 | Located in Canon City, CO -- | skip |
| 3076 | Located in Canon City, CO -- | LOT: New MISC New and Used motor/gearboxes/airlock: (4)Motors (2)WNM 3phase 1hp 1140rpm 208/230/460 (1)WNM 3phase 2hp 1170rpm 208/230/460v (1) WNM 3phase 2hp 1170rpm 208/230/460v (1) CF3- Cyclone Airlock C3391007 (17) drive to drive's laoding fee $50 |
| 3077 | Located in Canon City, CO -- | Lot: 5 airlock with sightglass,, 1 standard airlock(new replacement cost approximately $3000 each) loading fee $50 |
| 3078 | Located in Canon City, CO -- | Lot: Sprout force 501 force feeder(new replacment cost $6900), motor, 50 shear pin collar (new replacement cost $900), sprout knife holder etc loadng fee $50 |
| 3079 | Located in Canon City, CO -- | Lot: Misc spare parts: pulley, feed chutes loading fee $50 |
| 3080 | Located in Canon City, CO -- | Lot: Misc spare parts loading fee $50 |
| 3081 | Located in Canon City, CO -- | Lot: sprout 501 shroud, seal plate, shear pin collar, loading fee $50 |
| 3082 | Located in Canon City, CO -- | New/unused CME Large C10 airlock, no drive (replacment cost $3200) loading fee $50 |
| 3083 | Located in Canon City, CO -- | Lot: New/unused pellet mill force feeders loading fee $50 |
| 3084 | Located in Canon City, CO -- | LOT: Greasers/Lubricator parts loading fee $50 |
| 3085 | Located in Canon City, CO -- | Sprout 501 mainshaft (new replacement cost $9500) loading fee $50 |
| 3086 | Located in Canon City, CO -- | Lot: sprout 501 mainshaft (new replacement cost $9500) and feedcone loading fee $50 |
| 3087 | Located in Canon City, CO -- | Sprout mainshaft for 3 roll pellet mill for sprout 26 pellet mill(new replacement cost approx $15,000) loading fee $50 |
| 3088 | Located in Canon City, CO -- | Lot: 2 cpm pinion gears loading fee $50 |
| 3089 | Located in Canon City, CO -- | Lot: 4 CPM century Mainshafts, loading fee $50 |
| 3090 | Located in Canon City, CO -- | Lot: 4 CPM pellet mill quills loading fee $50 |
| 3091 | Located in Canon City, CO -- | Lot: 3 CPM Century pellet mill quills loading fee $50 |
| 3092 | Located in Canon City, CO -- | Century quill loading fee $50 |
| 3093 | Located in Canon City, CO -- | Lot: 4 Century Quills loading fee $50 |
| 3094 | Located in Canon City, CO -- | Lot 4 Century quills loading fee $50 |
| 3095 | Located in Canon City, CO -- | Lot 4 cpm pellet mill quills loading fee $50 |
| 3096 | Located in Canon City, CO -- | Box of bearings and misc parts for CPM 3000 and 7000(1)New 7000 Main Shaft Bearing (1)New 3020 MainShaft Timken Bearing (1)New 24030 cc/w33 SKF Bearing (2) loading fee $50 |
| 3097 | Located in Canon City, CO -- | Lot: rectangular to round (2)16"x9 1/2"x12"round (1)18 1/2"x12"x14"round (1)23 1/2"x14 1/2"x16"round loading fee $50 |
| 3098 | Located in Canon City, CO -- | Lot:1 Pallet of 2 Sprout dies with stiffener rings loading fee $50 |
| 3098A | Located in Canon City, CO -- | LOT:1 crate of hinges, knife post assemblies spanner nuts, loading fee $50 (wear rings in pic not included) |
| 3098B | Located in Canon City, CO -- | LOT: 2 sprout wear rings loading fee $50 (wear rings only no other parts included) |
| 3099 | Located in Canon City, CO -- | New CME C10 Cyclone with top mounted blower and motor Baldor 15hp, 3480 rpm, 230/460v W/Fan Rated at approximately 5000 cfm at 12" static pressure for use with hammermills, pellet coolers, almond powder coating, etc, (new cost $8900) ships on 3 pallets, loading fee $100 |
| 3100 | Located in Canon City, CO -- | Leblond Lathe Swing 15", Distance between centers 54", D1-6" Chuck Included, Servo Shift, 30-1800 RPM, No Tool Holder, loading fee $100 |
| 3101 | Located in Canon City, CO -- | CPM Conditioner w/motor 25hp 8.5' long conditioner, last running with CPM 9036 large pellet mill(new replacement cost approximately $30,000) loading fee $100 |
| 3102 | Located in Canon City, CO -- | LOT: CPM Chute, door backplate etc loading fee $50 |
| 3103 | Located in Canon City, CO -- | LOT: Sprout 501H Base with feed cone and belting loading fee $100 |
| 3104 | Located in Canon City, CO -- | Lot 3 new CME Cyclones rated at approximately at up to 1500cfm commonly used used HMA30 hammermills (new cost $1200 each) loading fee $100 |
| 3105 | Located in Canon City, CO -- | skip |
| 3106 | Located in Canon City, CO -- | Discontinued 40"x120" double deck screener, with isolation stand(missing 2 cables) no motor loading fee $100 |
| 3107 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand with cables, loading fee $100 |
| 3108 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand,(missing cover) loading fee $100 |
| 3109 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand with cables, loading fee $100 |
| 3110 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand and calbes, loading fee $100 |
| 3111 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand, loading fee $100 |
| 3112 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand, loading fee $100 |
| 3113 | Located in Canon City, CO -- | Discontinued 40"x84" double deck screener, no motor, with isolation stand, loading fee $100 |
| 3114 | Located in Canon City, CO -- | CPM Gearbox #202-320818 with misc parts loading fee $100 |
| 3115 | Located in Canon City, CO -- | CPM S/N: #202-295717, last running with a 250hp motor and using a 22" die. loading fee $100 |
| 3116 | Located in Canon City, CO -- | Sprout Andritz die approx 36" diameter with 1/8 holes probably for PM919XW 3" overall thickness loading fee $50 |
| 3117 | Located in Canon City, CO -- | skip |
| 3118 | Located in Canon City, CO -- | CPM die 30" diameter and 3/16 holes for CPM 7800 3" overall thickness loading fee $50 |
| 3119 | Located in Canon City, CO -- | skip |
| 3120A | Located in Canon City, CO -- | skip |
| 3120B | Located in Canon City, CO -- | CPM 3020 die (Bottom Die Only) approx 1/4 holes x 2-3/4 effective loading fee $50 |
| 3121A | Located in Canon City, CO -- | Sprout Die 26"(top die only) wide die approx 3/16 x 2-1/4, 2 1/2" overall thickness loading fee $50 |
| 3121B | Located in Canon City, CO -- | Sprout Die 26 (bottom die only) die approx 1/4" x 1-3/4" eff loading fee $50 |
| 3122 | Located in Canon City, CO -- | LOT: 2 CPM Dies 7000 22.5" approx 1/4" X 3 EFF loading fee $50 |
| 3123 | Located in Canon City, CO -- | LOT: 2 Sprout 1/4" Die approx 1/4" X 1 1/4 EFF & 1/4" X 2 3/4 EFF loading fee $50 |
| 3124 | Located in Canon City, CO -- | CPM Hyflow die approx 3/16 x 2" effective loading fee $50 |
| 3125 | Located in Canon City, CO -- | CPM Century 1/4 die approx 1-3/8 effective loading fee $50 |
| 3126 | Located in Canon City, CO -- | Sprout Ace Die approx with oval extrusion approx 11/16"x5/16" x 5" overall thickness loading fee $50 |
| 3127 | Located in Canon City, CO -- | CPM 7000 Die approx 1/4" X 1 1/4 EFF loading fee $50 |
| 3128 | Located in Canon City, CO -- | CPM 3020 Die 3/4" x 5" loading fee $50 |
| 3129 | Located in Canon City, CO -- | CPM 7000 1/4 die x approx 3 eff loading fee $50 |
| 3130 | Located in Canon City, CO -- | CPM 3020 die approx 3/16" x 2 1/4" overall thickness loading fee $50 |
| 3131 | Located in Canon City, CO -- | LOT 2: Sprout 26" die 1/4" Dies loading fee $50 |
| 3132 | Located in Canon City, CO -- | Sprout 32" Die: approx 1/4" X 2 1/2 EFF loading fee $50 |
| 3133 | Located in Canon City, CO -- | LOT: 4 Sprout 32" dies with 1/4 hole: 1/4" Die with approx 2" to 2.5" effective loading fee $50 |
| 3134 | Located in Canon City, CO -- | Inside Dia: 20"" Extruder size: 3/16" Die Type: Clamp on CPM, 3/16" X 1 3/4 EFF loading fee $50 |
| 3135 | Located in Canon City, CO -- | Lot: 2 Sprout 26” die for approx 1/4” and 3/16 pellets, loading fee $50 |
| 3136 | Located in Canon City, CO -- | CPM 3020 Die approx 1/4" X 1 3/4" EFF loading fee $50 |
| 3137 | Located in Canon City, CO -- | Lot: Misc parts, gears, and plastic conveyor links Loading fee $50 |
| 3138 | Located in Canon City, CO -- | 3M Box Sealer 52" x 30" x 57" high loading fee $50 |
| 3139 | Located in Canon City, CO -- | skip |
| 3140 | Located in Canon City, CO -- | skip |
| 3141 | Located in Canon City, CO -- | skip |
| 3142 | Located in Canon City, CO -- | skip |
| 3143 | Located in Canon City, CO -- | LOT 2 CPM 7000 die 1/4 Loading fee |
| 3144 | Located in Canon City, CO -- | LOT 3 CPM century dies: approx Cube DIe (1)1/2" Square Cube (1) 3/16" X 2 1/4 EFF (1)3/16" X 2 1/4 EFF loading fee $50 |
| 3145 | Located in Canon City, CO -- | Lot: 2 CPM 16" dies for Roughager, early century, 8 keys on die, uses clamp on feed cone, 2 1/4" overall thickness, size approximately 11/64ths with 2" effectuve loading fee $50 |
| 3146 | Located in Canon City, CO -- | Lot: 2 CPM 3020 wide 7/8 Cube dies, 5" overall thickness, 7/8" X 3 1/2 EFF loading fee $50 |
| 3147 | Located in Canon City, CO -- | Lot: Misc Control panels loading fee $50 |
| 3148 | Located in Canon City, CO -- | Inside Dia: 36" Extruder size: 3/16"" Die Type: Bolt on Sprout, 3" overall thickness loading fee $50 |
| 3149 | Located in Canon City, CO -- | Inside Dia: 36" Extruder size: 3/16"" Die Type: Bolt on Sprout, 3" overall thickness loading fee $50 |
| 3150 | Located in Canon City, CO -- | Inside Dia: 36" Extruder size: 3/16"" Die Type: Bolt on Sprout, 3" overall thickness loading fee $50 |
| 3151 | Located in Canon City, CO -- | Inside Dia: 36" Extruder size: 3/16"" Die Type: Bolt on Sprout, 3" overall thickness loading fee $50 |
| | Located in Canon City, CO -- | skip |
| 3152 | Located in Canon City, CO -- | LOT 2 CPM 7000 Dies 3/16" by appox 1 1/2" EFF, loading fee $100 |
| 3153 | Located in Canon City, CO -- | Lot: 5 Sprout front plates for sprout 26 with 2 front deflectors, and 3 sprout front deflector for sprout 21 loading fee $50 |
| 3154 | Located in Canon City, CO -- | Canco American Can 06 can seamer,423-IES-00 closing machine SN 4165 last running at a facility that processed nuts loading fee $100 |
| 3155 | Located in Canon City, CO -- | Vermeer HBP520 Block Brick Machine, Very low hours, Kohler 20hp engine, portable , for making compressed soil bricks loading fee $100 |
| 3156 | Located in Canon City, CO -- | CPM quill loading fee $50 |
| 3157 | Located in Canon City, CO -- | CPM quill loading fee $50 |
| 3158 | Located in Canon City, CO -- | Lot: Misc Sprout parts including feed cone, stiffener ring and roll shell loading fee $50 |
| 3159 | Located in Canon City, CO -- | Lot: 2 Sprout 26" dies approx 1/4" , 3" overall thickness, 2) 1/4" X 2 3/4 EFF, loading fee $50 |
| 3160 | Located in Canon City, CO -- | Sprout 26" Cube approx 1/2 holes loading fee $50 |
| 3161 | Located in Canon City, CO -- | 7000 Parts frontbearing housings (out of spec) loading fee $50 |
| 3162 | Located in Canon City, CO -- | Lot: spare parts including sprout 501, door seal rings, front plates with ribbon deflector loading fee $50 |
| 3163 | Located in Canon City, CO -- | Lot: 2 501 mainshafts, 2 501 shear pin collar and mainshaft nut loading fee $50 |
| 3164 | Located in Canon City, CO -- | Lot: CPM Mainshaft and quill loading fee $50 |
| 3165 | Located in Canon City, CO -- | Lot : Misc spare parts 7000 shear pin inner and outer, hinges loading fee $50 |
| 3166 | Located in Canon City, CO -- | Lot: 501 Roll Shells and die clamps loading fee $50 |
| 3167 | Located in Canon City, CO -- | Lot: CPM gearbox cartridges loading fee $50 |
| 3168 | Located in Canon City, CO -- | Sprout stainless feeder conditioner screw and paddle shaft spin independently loading fee $50 |
| 3169 | Located in Canon City, CO -- | Sprout stainless feeder conditioner, no drive motor (approx new replacement cost $20,000) loading fee $50 |
| 3170 | Located in Canon City, CO -- | Lot: CPM dual speed quills, mainshafts, main gear and misc parts loading fee $50 |
| 3171 | Located in Canon City, CO -- | Lot: CPM dual speed parts gears loading fee $50 |
| 3172 | Located in Canon City, CO -- | Lot: Misc rollers and captive bearings loadingfee $50 |
| 3173 | Located in Canon City, CO -- | CPM DS casting gearbox loading fee $50 |
| 3174 | Located in Canon City, CO -- | Jacobson Type Tear drop shaped screens (30"x24") (three size diameters: 1/8", 5/8", 1/2") loading fee $50 |
| 3175 | Located in Canon City, CO -- | CPM Quill with bearings loading fee $50 |
| 3176 | Located in Canon City, CO -- | CPM Quill with bearings loading fee $50 |
| 3177 | Located in Canon City, CO -- | Forklift engine loading fee $50 |
| 3178 | Located in Canon City, CO -- | Lot: misc pellet mill parts loading fee $50 |
| 3179 | Located in Canon City, CO -- | Rockwell Hardness tester, Model 3 SS 0 #73 loading fee $50 |
| 3180 | Located in Canon City, CO -- | Lot: Misc electric hoists loading fee $50 |
| 3181 | Located in Canon City, CO -- | Rotor reported for 4420 hammermill 32-1/2" x 18-3/8" Rotor w/ 5 spaces loading fee $50 |
| 3182 | Located in Canon City, CO -- | Rotor reported for 4424 hammermill 32-1/2" x 23-1/2" Rotor w/ 7 spaces loading fee $50 |
| 3183 | Located in Canon City, CO -- | Lot: Misc bearings and parts loading fee $50 |
| 3184 | Located in Canon City, CO -- | skip |
| 3185 | Located in Canon City, CO -- | skip |
| 3186 | Located in Canon City, CO -- | skip |
| 3187 | Located in Canon City, CO -- | Chute w/ magnet IN:22 5/8" x 16 1/2" OUT: 23 1/8" x13" TALL: 14 1/2" loading fee $50 |
| 3188 | Located in Canon City, CO -- | skip |
| 3189 | Located in Canon City, CO -- | LOT: Misc CPM feed cones loading fee $50 |
| 3190 | Located in Canon City, CO -- | skip |
| 3191 | Located in Canon City, CO -- | Lot: 13 Gears from CPM pellet mills loading fee $50 |
| 3192 | Located in Canon City, CO -- | Misc electric box 24" x 24" x 13" deep loading fee $50 |
| 3193 | Located in Canon City, CO -- | Lot: Various hinges from CPM pellet mills and 1 magnet loading fee $50 |
| 3194 | Located in Canon City, CO -- | CPM Feed Cones and clamps loading fee $50 |
| 3195 | Located in Canon City, CO -- | Feed cones loading fee $50 |
| 3196 | Located in Canon City, CO -- | skip |
| 3197 | Located in Canon City, CO -- | Lot: Misc steel parts- loading fee $50 |
| 3198 | Located in Canon City, CO -- | CPM Dual Speed Housings- loading fee $50 |
| 3199 | Located in Canon City, CO -- | skip |
| 3200 | Located in Canon City, CO -- | Dual speed cartridge housing (no feed cones) loading fee $50 |
| 3201 | Located in Canon City, CO -- | CPM Century Gear Box, Loading fee $50 |
| 3202 | Located in Canon City, CO -- | Lot: Various stiffener rings, wear ring, front plate etc loading fee $50 |
| 3203 | Located in Canon City, CO -- | CPM Century Gear Box with main gear and quill, loading $50 |
| 3204 | Located in Canon City, CO -- | CPM 100DS1S Gearbox with loading fee $50 |
| 3205 | Located in Canon City, CO -- | CPM Century Gear Box loading fee $50 |
| 3206 | Located in Canon City, CO -- | CPM Century Gear Box, Loading fee $50 |
| 3207 | Located in Canon City, CO -- | Weighing Machine last running nuts on a can seaming line, loading fee $50 |
| 3208 | Located in Canon City, CO -- | Double vacuum box small can, loading fee $50 |
| 3209 | Located in Canon City, CO -- | Twin vacuum box, loading fee $50 |
| 3210 | Located in Canon City, CO -- | Conveyer last running in canning line, loading fee $50 |
| 3211 | Located in Canon City, CO -- | conveyor last running in canning line, loading fee $50 |
| 3212 | Located in Canon City, CO -- | Jeffery Rader TerraSource Model 34 SN 12405 Terra Source Wood Hog last running wood , no motor loading fee $100 |
| 3213 | Located in Canon City, CO -- | CPM Door and feed chute for CPM 9000, loading fee $50 |
| 3214 | Located in Canon City, CO -- | Toshiba Electric Motor 600hp 1800rpm, 440V 5810US loading fee $100 |
| 3215 | Located in Canon City, CO -- | Lot: 3 pellet mill mainshafts, front plate, rear hub etc, loading fee $50 |
| 3216 | Located in Canon City, CO -- | New/unused brick making machine wth Honda engine, makes adobe cement contruction bricks, (new replacement cost $50,000) loading fee $50 |
| 3217 | Located in Canon City, CO -- | Lot, 25hp rated blower housing, fan wheel, ductwork, loading $50 |
| 3218 | Located in Canon City, CO -- | Lot, 25hp rated blower housing, fan wheel, ductwork, loading $50 |
| 3219 | Located in Canon City, CO -- | Blower and Duct Work, loading fee $50 |
| 3220 | Located in Canon City, CO -- | Sprout 26" Die 1/4", loading fee $50 |
| 3221 | Located in Canon City, CO -- | CPM 30" Die 1/4" Die 2 1/2" overall thickness, loading fee $50 |
| 3222 | Located in Canon City, CO -- | Transformer, loading fee $50 |
| 3223 | Located in Canon City, CO -- | Atlas Copco air compressor GA509 air compressor, loading fee $100 |
| 3224 | Located in Canon City, CO -- | Lot: Misc steel parts from large CPM pellet Mill, loading fee $50 |
| 3225 | Located in Canon City, CO -- | CPM 7000 Conditioner and Feeder with magnet and motor Teco-Westinghouse 10hp 885rpm 230/460v, loading fee $50 |
| 3226 | Located in Canon City, CO -- | CPM large conditioner with motor no name plate, loading fee $50 |
| 3227 | Located in Canon City, CO -- | Unused CME R100 Pellet Mill 100hp motor with dual 50hp motor and conditioner, force feeder, 1 set of rolls, and autolube system. loading fee $50 |
| 3227A | Located in Canon City, CO -- | LOT: 3 NEW R100 pellet mill ring dies bottom pallet loading fee $50 in lower warehouse, loading fee $50 |
| 3227B | Located in Canon City, CO -- | R100 mainshaft for 100hp hp pellet mill, replacement cost $6900 loading fee $50 in lower warehouse, loading fee $50 |
| 3227C | Located in Canon City, CO -- | Lot: Misc CME R100 rolls, roll shells, clamps, feed cone, gearbox, shafts, and misc pellet mill parts in lower warehouse, loading fee $100 |
| 3228 | Located in Canon City, CO -- | Lot: Misc Duct Work Blower Housing with fan blade, loading fee $50 |
| 3229 | Located in Canon City, CO -- | skip |
| 3230 | Located in Canon City, CO -- | skip |
| 3231 | Located in Canon City, CO -- | skip |
| 3232 | Located in Canon City, CO -- | Leeson 40hp 1780rpm 230/460v, Teco/Westinghouse 50hp 1800rpm 230/460v, loading fee $50 |
| 3233 | Located in Canon City, CO -- | LOT 8 Motors (1)World Wide 7.5hp 3520rpm 230/460v 213tc frame (1)Reliance Electric Sabre 5hp 1740rpm 208-230/460v 184tc frame (1)Baldor 3hp 1725rpm 208-230/460v 182tc frame (1)Baldor 1/3hp 1750rpm 90dc volts327-pslh-0 frame (1)Marathon DAMAGED TAG (1) Brook Hansen .33hp 1680rpm230/460v D71F frame (1)Baldor .5hp 1725rpm 208-230/460v 56C frame(1)Reliance Electric 1/2hp 1725rpm 115/230v FB56C frame loading fee $50 |
| 3234 | Located in Canon City, CO -- | Reliance 20hp 3525rpm 460v, loading fee $50 |
| 3235 | Located in Canon City, CO -- | Misc. Duct Work and transitions, loading fee $50 |
| 3236 | Located in Canon City, CO -- | Bliss hammermill feed chute with 40" wide magnet, loading fee $50 |
| 3237 | Located in Canon City, CO -- | skip |
| 3238 | Located in Canon City, CO -- | Motor No name plate shaft dia. 1 5/8", loading fee $50 |
| 3239 | Located in Canon City, CO -- | skip |
| 3240 | Located in Canon City, CO -- | skip |
| 3241 | Located in Canon City, CO -- | Lot: CPM feed chutes, century rear scrapers, front scraper, front plate, rear plate, bearings, seal rings, loading fee $50 |
| 3242 | Located in Canon City, CO -- | Surface grinder with boyar dustcollector model 612 serialno.3197H motor: 1/3hp 220/60/3-1.5amp , loading fee $500 |
| 3243 | Located in Canon City, CO -- | LOT: misc. parts including coupling elements, fastener, spanner nuts, springs etc, loading fee $50 |
| 3244 | Located in Canon City, CO -- | Lot: gear reducers, pulleys, xp vibration sensors, and misc parts, loading fee $50 |
| 3245 | Located in Canon City, CO -- | LOT: Misc cpm pellet mill parts, loading fee $50 |
| 3246 | Located in Canon City, CO -- | Lot: CPM shear pin parts, coupling, bearings, and misc parts, loading fee $50 |
| 3247 | Located in Canon City, CO -- | CPM Door for century pellet mill, loading fee $50 |
| 3248 | Located in Canon City, CO -- | CPM pump system, loading fee $50 |
| 3249 | Located in Canon City, CO -- | Lot: Misc couplings, spanner nuts lock washers etc, loading fee $50 |
| 3250 | Located in Canon City, CO -- | skip |
| 3251 | Located in Canon City, CO -- | Lot CPM century and master main shafts, loading fee $50 |
| 3251A | Located in Canon City, CO -- | LOT: CPM pinion gears, loading fee $50 |
| 3252 | Located in Canon City, CO -- | CPM 7000 1/4" die loading fee $50 |
| 3253 | Located in Canon City, CO -- | Lot: 3 - 1hp 1200 rpm c face motors, 1 - approx 15hp 3600rpm Electric Motors, loading fee $50 |
| 3254 | Located in Canon City, CO -- | LOT: CPM Bull Gear, CPM 16" backplate, and coupling, loading fee $50 |
| 3255 | Located in Canon City, CO -- | (2) Reliance Electric 30hp 3535rpm 230/460v, loading fee $50 |
| 3256 | Located in Canon City, CO -- | Lot: Misc pellet mill parts, motor slide plate, loading fee $50 |
| 3257 | Located in Canon City, CO -- | Lot: CPM front roll support plates etc, loading fee $50 |
| 3258 | Located in Canon City, CO -- | Lot: Misc motors, gearboxes, sensors etc , loading fee $50 |
| 3259 | Located in Canon City, CO -- | CPM Quill, loading fee $50 |
| 3260 | Located in Canon City, CO -- | LOT: Pellet mill pinion gears, loading fee $50 |
| 3261 | Located in Canon City, CO -- | LOT: pallet and box of tubes, hoses, simplex cylinders etc loading fee $50 |
| 3262 | Located in Canon City, CO -- | Lot: CPM Cartridge, Frontplate, pinion gear and misc parts, loading fee $50 |
| 3263 | Located in Canon City, CO -- | Pellet Mill Bull Gear, loading fee $50 |
| 3264 | Located in Canon City, CO -- | Misc. Sprout 501 main shaft and roll shells, and misc pellet mill parts loading fee $50 |
| 3265 | Located in Canon City, CO -- | Lot: pinion and bull gear appear to be for sprout 26 N pellet mill, loading fee $50 |
| 3266 | Located in Canon City, CO -- | skip |
| 3267 | Located in Canon City, CO -- | LOT: Motors (1)GE 1 1/2hp 1160rpm 230/460v (1) SB 7.5kw 1450 rpm 380v (1) 30hp 1780rpm 230/460v, loading fee $50 |
| 3268 | Located in Canon City, CO -- | Lot: CPM mainshafts, frontplates, backplates, shearpin housings, and misc parts , gear, wearing etc loading fee $50 |
| 3269 | Located in Canon City, CO -- | Lot: 9 CPM stainless door backplates, loading fee $50 |
| 3270 | Located in Canon City, CO -- | skip |
| 3271 | Located in Canon City, CO -- | LOT: CPM Master Dies, Approx 1/4" X 1 1/2 EFF, 2)1/8" X 1.0 EFF, 1/8" X 1 1/2 EFF, loading fee $50 |
| 3272a | Located in Canon City, CO -- | LOT: 3 CPM 7000 Feed Cone, Knife Assembly, die clamps etc loading fee $50 |
| 3272b | Located in Canon City, CO -- | New CME C10 hopper no legs, loading fee $50 |
| 3273a | Located in Canon City, CO -- | Lot: Misc. Pellet Mill Parts, loading fee $50 |
| 3273b | Located in Canon City, CO -- | LOT: wipers and deflectors etc, loading fee $50 |
| 3274 | Located in Canon City, CO -- | skip |
| 3275 | Located in Canon City, CO -- | Lot CPM pellet mill parts, loading fee $50 |
| 3276 | Located in Canon City, CO -- | Lot: Die clamp and wear rings, loading fee $50 |
| 3277 | Located in Canon City, CO -- | Lot: 6 sprout dies(5/8, 1/4, 1/8, 5/16) and 1 cpm die, loading fee $50, |
| 3278 | Located in Canon City, CO -- | Lot: Misc CPM parts, loading fee $50 |
| 3279 | Located in Canon City, CO -- | Lot: misc pellet mill knive parts, loading fee $50 |
| 3280 | Located in Canon City, CO -- | Sprout Andritz Feeder Conditioner for 26" pellet mill , loading fee $100 |
| 3281 | Located in Canon City, CO -- | Lot: clamps for cpm pellet mill , loading fee $50 |
| 3282 | Located in Canon City, CO -- | CPM 7000 Quill , loading fee $50 |
| 3283 | Located in Canon City, CO -- | CPM 7000 Quill, loading fee $50 |
| 3284 | Located in Canon City, CO -- | NEW CME C5 Cooler discharge hopper, loading fee $50 |
| 3285 | Located in Canon City, CO -- | CME C5 screener no stand no motor, loading fee $50 |
| 3286 | Located in Canon City, CO -- | Jacobson 2436 hammermill with 200hp 3600 rpm motor , heavy duty design, and magnet, last running in a wood pellet plant, loading fee $100 |
| 3287 | Located in Canon City, CO -- | Misc. Screens, loading fee $50 |
| 3288 | Located in Canon City, CO -- | Drum with stand, loading fee $50 |
| 3289 | Located in Canon City, CO -- | Taylor OM2A bagging scale last running wood pellets, loading fee $50 |
| 3290 | Located in Canon City, CO -- | Screw feeder with motor and stand 7'-7" x 12", loading fee $50 |
| 3291 | Located in Canon City, CO -- | Hopper for williams hog, loading fee $50 |
| 3292 | Located in Canon City, CO -- | 50hp hammermill no motor, with spare screens, loading fee $50 |
| 3293 | Located in Canon City, CO -- | Airlock inlet 13 5/8" x 13 1/4", loading fee $50 |
| 3294 | Located in Canon City, CO -- | CPM feedershell and conditioner shell (no screw or paddles) last running on CPM 250hp pellet mill, loading fee $50 |
| 3295 | Located in Canon City, CO -- | steel conveyor, no belting loading fee $50 |
| 3296 | Located in Canon City, CO -- | skip |
| 3297 | Located in Canon City, CO -- | Drive-All gearbox with sprout 10 groove 501 pulley with ss seal plates, loading fee $50 |
| 3298 | Located in Canon City, CO -- | Sprout 501 mainshaft, dieshousing and pulley cartridge, and door seal plates, loading fee $50 |
| 3299 | Located in Canon City, CO -- | Steel stand with guard, loading fee $50 |
| 3300 | Located in Canon City, CO -- | skip |
| 3301 | Located in Canon City, CO -- | InterSystems model:900841 product distributor , loading fee $50 |
| 3302 | Located in Canon City, CO -- | Lot: Hammermill screens (12) 1/4" (1) 1/2", loading fee $50 |
| 3303 | Located in Canon City, CO -- | Hammermill magnet with chute, loading fee $50 |
| 3304 | Located in Canon City, CO -- | Steel pan loading fee $50 |
| 3305 | Located in Canon City, CO -- | steel ducting, loading fee $50 |
| 3306 | Located in Canon City, CO -- | steel ducting , loading fee $50 |
| 3307 | Located in Canon City, CO -- | Lot: MISC CPM Parts, 4 century dies, clamps, share pin housing, shear pins, bearing, shafts, scrapers, wipers, roll adjusters, shells, gears and misc parts, motor reducers etc, loading fee $50 |
| 3308 | Located in Canon City, CO -- | Sprout stainless feeder conditioner, loading fee $50 |
| 3309 | Located in Canon City, CO -- | Sprout 26 pellet mill door with force feeder , loading fee $50 |
| 3310 | Located in Canon City, CO -- | CPM 2GA2 cooler base, loading fee $50 |
| 3311 | Located in Canon City, CO -- | skip |
| 3312 | Located in Canon City, CO -- | Steel riser, loading fee $50 |
| 3313 | Located in Canon City, CO -- | Unused cyclone 9' tall x 4' round, loading fee $50 |
| 3314 | Located in Canon City, CO -- | skip |
| 3315 | Located in Canon City, CO -- | skip |
| 3316 | Located in Canon City, CO -- | skip |
| 3317 | Located in Canon City, CO -- | skip |
| 3318 | Located in Canon City, CO -- | skip |
| 3319 | Located in Canon City, CO -- | Lot Misc steel parts, loading fee $50 |
| 3320 | Located in Canon City, CO -- | LOT: 9 Unused CME bins 38 1/2" X 42" X 19" tall no legs, loading fee $50 |
| 3321 | Located in Canon City, CO -- | Lot steel cage with cpm parts and feed cones, loading fee $50 |
| 3322 | Located in Canon City, CO -- | Lot: Sprout 26 die stiffener ring and wear ring, loading fee $50 |
| 3323 | Located in Canon City, CO -- | conveyor with drive and bin, loading fee $50 |
| 3324 | Located in Canon City, CO -- | century 125hp electric motor, 1170 rpm 460V 445T loading fee $100 |
| 3325 | Located in Canon City, CO -- | Lot: 2 Torit dust colletctors, loading fee $50 |
| 3326 | Located in Canon City, CO -- | Lot: Misc Chutes, loading fee $50 |
| 3327 | Located in Canon City, CO -- | Lot: Misc Gearboxes and vibratory tray, loading fee $50 |
| 3328 | Located in Canon City, CO -- | Lot: 4 heavy duty stands (2) 50" X 44 1/2" X 37" tall (2) 50" X 44 1/4" X 42 5/8" tall, loading fee $50 |
| 3329 | Located in Canon City, CO -- | Bliss rotary pocket feeder with drive , loading fee $50 |
| 3330 | Located in Canon City, CO -- | CPM large conditioner with motor, loading fee $50 |
| 3331 | Located in Canon City, CO -- | Single deck screener mounted on a stand, loading fee $50 |
| 3332 | Located in Canon City, CO -- | spare screens $50 |
| 3333 | Located in Canon City, CO -- | Heil rotary single pass drum dryer with trunions 10.5' x 32', last running alfalfa, loading fee $500 |
| 3334 | Located in Canon City, CO -- | Sprout pellet mill approximately 250hp, no motor loading fee $100 |
| 3335 | Located in Canon City, CO -- | Sprout screener approximately 5 x 10 with motor / drive, loading fee $100 |
| 3336 | Located in Canon City, CO -- | Heil 8 x 24 rotary drum with trunions, loading fee $500 |
| 3337 | Located in Canon City, CO -- | Simplicity vibratory conveyor, last running in a wood pellet plant feeding a horizontal hog, loading fee $100 |
| 3338 | Located in Canon City, CO -- | CPM Pellet mill base with misc parts, loading fee $50 |
| 3339 | Located in Canon City, CO -- | Lot: 2 CPM doors and CPM base, loading fee $50 |
| 3340 | Located in Canon City, CO -- | SS CPM pellet mill door with knife posts, and misc parts, loading fee $50 |
| 3341 | Located in Canon City, CO -- | Steel plates, and pulley, loading fee $50 |
| 3342 | Located in Canon City, CO -- | Steel beams and riser, loading fee $50 |
| 3343 | Located in Canon City, CO -- | CPM pellet mill door with stainless feed chute and knife posts, CPM base and die, loading fee $50 |
| 3344 | Located in Canon City, CO -- | skip |
| 3345 | Located in Canon City, CO -- | riser, loading fee $50 |
| 3346 | Located in Canon City, CO -- | CPM Pellet mill base, loading fee $50 |
| 3347 | Located in Canon City, CO -- | CPM Pellet Mill base, loading fee $50 |
| 3348 | Located in Canon City, CO -- | CPM Pellet Mill base, loading fee $50 |
| 3349 | Located in Canon City, CO -- | CPM Pellet Mill door backplate, feed chute, and base; sprout 501 die housing, loading fee $50 |
| 3350 | Located in Canon City, CO -- | CPM pellet Mill base, loading fee $50 |
| 3351 | Located in Canon City, CO -- | CPM Century Door with feed chute and knife post, loading fee $50 |
| 3352 | Located in Canon City, CO -- | SS screw feeer housing, loading fee $50 |
| 3353 | Located in Canon City, CO -- | Lot: 2 CPM Bases, loading fee $50 |
| 3354 | Located in Canon City, CO -- | Auger stainless shell mild steel screw no drive, loading fee $50 |
| 3355 | Located in Canon City, CO -- | LOT: Misc screen mesh, loading fee $50 |
| 3356 | Located in Canon City, CO -- | Steel riser, loading fee $50 |
| 3357 | Located in Canon City, CO -- | LOT: 4 risers 41" x 62", 75" X 41 1/2" (1) 10" (1) 8" (1)15", loading fee $50 |
| 3358 | Located in Canon City, CO -- | Sprout force feeder for 26" pellet mill, loading fee $50 |
| 3359 | Located in Canon City, CO -- | CPM pellet Mill Base, loading fee $50 |
| 3360 | Located in Canon City, CO -- | CPM Century door, loading fee $50 |
| 3361 | Located in Canon City, CO -- | CPM 3020 new pellet mill door, never used/installed loading fee $50 |
| 3362 | Located in Canon City, CO -- | CPM SS door loading fee $50 |
| 3363 | Located in Canon City, CO -- | Stainless door with force feeder, loading fee $50 |
| 3364 | Located in Canon City, CO -- | CPM SS door with feed chute, loading fee $50 |
| 3365 | Located in Canon City, CO -- | Lot: 2 set of roller conveyor, loading fee $50 |
| 3366 | Located in Canon City, CO -- | CPM pellet mill base, loading fee $50 |
| 3367 | Located in Canon City, CO -- | Steel base with infeed drum, loading fee $50 |
| 3368 | Located in Canon City, CO -- | CPM stainless door with feed chute, loading fee $50 |
| 3369 | Located in Canon City, CO -- | CPM century door, loading fee $50 |
| 3370 | Located in Canon City, CO -- | CPM door, loading fee $50 |
| 3371 | Located in Canon City, CO -- | CPM door, loading fee $50 |
| 3372 | Located in Canon City, CO -- | CPM SS door, loading fee $50 |
| 3373 | Located in Canon City, CO -- | skip |
| 3374 | Located in Canon City, CO -- | CPM Screw conveyor with magnet, loading fee $50 |
| 3375 | Located in Canon City, CO -- | CPM door, loading fee $50 |
| 3376 | Located in Canon City, CO -- | CPM stainless 201/7000 door, loading fee $50 |
| 3377 | Located in Canon City, CO -- | CPM door with feed chute, loading fee $50 |
| 3378 | Located in Canon City, CO -- | CPM door with feed chute, loading fee $50 |
| 3379 | Located in Canon City, CO -- | CPM 201/7000, loading fee $50 |
| 3380 | Located in Canon City, CO -- | CPM century door with knife assembly, loading fee $50 |
| 3381 | Located in Canon City, CO -- | LOT: 3 screener screens, loading fee $50 |
| 3382 | Located in Canon City, CO -- | LOT: Steel loading fee $50, loading fee $50 |
| 3383 | Located in Canon City, CO -- | Hopper bins with legs, loading fee $50 |
| 3384 | Located in Canon City, CO -- | Hopper bins with legs, loading fee $50 |
| 3385 | Located in Canon City, CO -- | Lot: 2 steel stands 8'-6 3/8" X 3'-9", loading fee $50 |
| 3386 | Located in Canon City, CO -- | LOT: Crate of control panels, switches, and motor gearbox, loading fee $50 |
| 3387 | Located in Canon City, CO -- | Horizontal feed hammer hog extreme duty, approximately 100-200hp, loading fee $100 |
| 3388 | Located in Canon City, CO -- | Steel stand, loading fee $50 |
| 3389 | Located in Canon City, CO -- | lOT: Misc Screen frames, loading fee $50 |
| 3390 | Located in Canon City, CO -- | Heavy duty sewing station, loading fee $50 |
| 3391 | Located in Canon City, CO -- | Lot: gear reducer, chain, and sprockets etc, loading fee $50 |
| 3392 | Located in Canon City, CO -- | Lot: approximately 70 screens 30" wide box of carbide hammers for champion hammermill, pluse other misc screens, about (90)hammers 10"×1 1/4" w/ 1 1/4" hole, screens (64) 1/16th 30"×5'. (7) 1/8th 30"×5'. (4) 3/8th 20"×5'. (4) 17 1/2"x3' w/1" holes , loading fee $50 |
| 3393 | Located in Canon City, CO -- | Lot: 12 warehouse racking beams and overhead crane beam, loading fee $50 |
| 3394 | Located in Canon City, CO -- | CPM Screw feeder with motor and drive loading fee $50 |
| 3395 | Located in Canon City, CO -- | CPM Stainless Steel Screw feeder with motor and drive, loading fee $50 |
| 3396 | Located in Canon City, CO -- | CPM Chute with magnet, and guard, loading fee $50 |
| 3397 | Located in Canon City, CO -- | CPM stainless conditioner, no drive, loading fee $50 |
| 3398 | Located in Canon City, CO -- | Sprout Andritz stainless steel feeder conditioner, last running on an Ace pellet mill, loading fee $50 |
| 3399 | Located in Canon City, CO -- | CPM feeder conditioner loading fee $50 |
| 3400 | Located in Canon City, CO -- | Sprout andritz stainless feeder conditoner loading fee $50 |
| 3401 | Located in Canon City, CO -- | CPM feeder loading fee $50 |
| 3402 | Located in Canon City, CO -- | Pellet mill stainless steel conditioner loading fee $50 |
| 3403 | Located in Canon City, CO -- | CPM feeder conditioner with drive loading fee $50 |
| 3404 | Located in Canon City, CO -- | skipped |
| 3405 | Located in Canon City, CO -- | Feeder with drive loading fee $50 |
| 3406 | Located in Canon City, CO -- | CPM stainless feeder loading fee $50 |
| 3407 | Located in Canon City, CO -- | CPM stainless feeder and conditioner with infeed chute, missing screw, loading fee $50 |
| 3408 | Located in Canon City, CO -- | Sprout 501 Ace door with knife holder loading fee $50 |
| 3409 | Located in Canon City, CO -- | Sprout 501 Ace door loading fee $50 |
| 3410 | Located in Canon City, CO -- | Lot: Misc piping and ductwork 14" Pipe/Duct loading fee $50 |
| 3411 | Located in Canon City, CO -- | 501 sprout guard loading fee $50 |
| 3412 | Located in Canon City, CO -- | LOT: Hinged motor base and steel plates loading fee $50 |
| 3413 | Located in Canon City, CO -- | skip |
| 3414 | Located in Canon City, CO -- | Stand 32" x 32" x 64"tall loading fee $50 |
| 3415 | Located in Canon City, CO -- | LOT: 4 Bliss pulleys loading fee $50 |
| 3416 | Located in Canon City, CO -- | Cement Mixer loading fee $50 |
| 3417 | Located in Canon City, CO -- | LOT: Biss pulley and feed chute, loading fee $50 |
| 3418 | Located in Canon City, CO -- | Bliss SS door to 400hp pellet mill with feed chute loading fee $50 |
| 3419 | Located in Canon City, CO -- | LOT: Bliss pulley guards, loading fee $50 |
| 3420 | Located in Canon City, CO -- | LOT: Bliss 400hp pellet mill frame, roll shells, feed cone, guard/plates, loading fee $100 |
| 3421 | Located in Canon City, CO -- | Sprout 21 pellet mill, missing parts, loading fee $100 |
| 3422 | Located in Canon City, CO -- | Lot: Cartridge for 400hp Bliss pellet mill, large pulleys, loading fee $50 |
| 3423 | Located in Canon City, CO -- | Chute loading fee $50 |
| 3424 | Located in Canon City, CO -- | Jeffery Rader Bar screener last running cube pellets loading fee $100 |
| 3425 | Located in Canon City, CO -- | LOT: Misc tubing/elbows loading fee $50 |
| 3426 | Located in Canon City, CO -- | LOT: Misc tubing/elbows loading fee $50 |
| 3427 | Located in Canon City, CO -- | LOT: Misc tubing/elbows loading fee $50 |
| 3428 | Located in Canon City, CO -- | CPM 100C pellet mill gearbox, air door, and base, and stand, no internal parts loading fee $10 |
| 3429 | Located in Canon City, CO -- | 75hp motor 440V 1140rpm with 10 groove pulley loading fee $50 |
| 3430 | Located in Canon City, CO -- | LOT: Misc tubing/elbows loading fee $50 |
| 3431 | Located in Canon City, CO -- | LOT: Misc tubing/elbows loading fee $50 |
| 3432 | Located in Canon City, CO -- | LOT: Misc tubing/elbows loading fee $50 |
| 3433 | Located in Canon City, CO -- | Sprout pellet mill base, loading fee $50 |
| 3434 | Located in Canon City, CO -- | LOT: Misc elbow loading fee $50 |
| 3435 | Located in Canon City, CO -- | LOT: Misc ductwork and tubing/elbows, loading fee $50 |
| 3436 | Located in Canon City, CO -- | LOT: (9)14 1/2" round ,(9)19 1/2" round ,(16)14 1/2" round, loading fee $50 |
| 3437 | Located in Canon City, CO -- | Sprout 501 pellet mill base loading fee $100 |
| 3438 | Located in Canon City, CO -- | LOT: Misc ductwork and tubing/elbows, loading fee $50 |
| 3439 | Located in Canon City, CO -- | LOT: Misc ductwork and tubing, loading fee $50 |
| 3440 | Located in Canon City, CO -- | Sprout 501H base loading fee $100 |
| 3441 | Located in Canon City, CO -- | Sprout 501 heavy groove pulley loading fee $50 |
| 3442 | Located in Canon City, CO -- | Lot: 2 chutes/transitions Loading fee $50 |
| 3443 | Located in Canon City, CO -- | Stainless chute for use above pellet mill, loading fee $50 |
| 3444 | Located in Canon City, CO -- | Sprout 501 base, loading fee $100 |
| 3445 | Located in Canon City, CO -- | Sprout 501 base, loading fee $100 |
| 3446 | Located in Canon City, CO -- | Sprout 501 base loading and stiffner ring loading fee $100 |
| 3447 | Located in Canon City, CO -- | Sprout 501 door and shroud loading fee $50 |
| 3448 | Located in Canon City, CO -- | Sprout 501 base and shroud loading fee $100 |
| 3449 | Located in Canon City, CO -- | Sprout 501HL base and used roll assembly loading fee $100 |
| 3450 | Located in Canon City, CO -- | CPM pellet mill gearbox case loading fee $50 |
| 3451 | Located in Canon City, CO -- | CPM century/roughager SN 188769 pellet mill gearbox case loading fee $50 |
| 3452 | Located in Canon City, CO -- | CPM gearbox case and door loading fee $50 |
| 3453 | Located in Canon City, CO -- | CPM garbox case and base loading fee $50 |
| 3454 | Located in Canon City, CO -- | CPM century gearbox loading fee $50 |
| 3455 | Located in Canon City, CO -- | CPM gearbox case loading fee $50 |
| 3456 | Located in Canon City, CO -- | Sprout 501H pellet mill base with door and extra shroud, missing cartridge, loading fee $100 |
| 3457 | Located in Canon City, CO -- | CPM 200 series gearbox case loading fee $50 |
| 3458 | Located in Canon City, CO -- | CPM Hyflo gearbox case loading fee $50 |
| 3459 | Located in Canon City, CO -- | CPM gearbox case loading fee $50 |
| 3460 | Located in Canon City, CO -- | LOT: CPM 200 series gearbox case and feed chute loading fee $50 |
| 3461 | Located in Canon City, CO -- | Sprout pellet mill door(rough condition) loading fee $50 |
| 3462 | Located in Canon City, CO -- | Sprout Andritz pellet mill door and feed chute (new replacement cost $4900 +2500) loading fee $50 |
| 3463 | Located in Canon City, CO -- | SS condtioner shell loading fee $50 |
| 3464 | Located in Canon City, CO -- | CPM ss feeder with drive(missing chain) loading fee $50 |
| 3465 | Located in Canon City, CO -- | CPM door with force feeder for 200-300hp pellet mill, loading fee $50 |
| 3466 | Located in Canon City, CO -- | Sprout 501 base, door and door and main pulley shroud, loading fee $100 |
| 3467 | Located in Canon City, CO -- | Blower paddle wheel fan, no motor, loading fee $50 |
| 3468 | Located in Canon City, CO -- | LOT: Sprout pellet mill door and stainless chute loading fee $50 |
| 3469 | Located in Canon City, CO -- | Sprout Andritz stainless feeder conditioner missing motor and some paddles loading fee $50 |
| 3470 | Located in Canon City, CO -- | Rotex 83 SN 24268 gearbox loading fee $50 |
| 3471 | Located in Canon City, CO -- | LOT CPM condtiioner shell and CPM stainless conditioner body with approx 15hp motor, conditioner stainless shell, loading fee $50 |
| 3472 | Located in Canon City, CO -- | LOT: stainless chutes, and cooler panels loading fee $50 |
| 3473 | Located in Canon City, CO -- | CPM feeder, stainless shell with drive loading fee $50 |
| 3474 | Located in Canon City, CO -- | Large CPM pellet mill door for use with 200-300hp door loading fee $10 |
| 3475 | Located in Canon City, CO -- | CPM pellet mill stainless steel conditioner loading fee $50 |
| 3476 | Located in Canon City, CO -- | Pacemaker 100hp 1780rpm 460v 405Tframe with CPM base loading fee $100 |
| 3477 | Located in Canon City, CO -- | skip |
| 3478 | Located in Canon City, CO -- | Heavy duty product feeder with drive loading fee $50 |
| 3479 | Located in Canon City, CO -- | Sprout stainless steel feeder conditioner loading fee $50 |
| 3480 | Located in Canon City, CO -- | Sprout feeder stainless steel conditioner loading fee $50 |
| 3481 | Located in Canon City, CO -- | CPM 7000 stainless steel conditioner loading fee $50 |
| 3482 | Located in Canon City, CO -- | Marathon 30hp 1765rpm 208-230/460v 286Tframe loading fee $50 |
| 3483 | Located in Canon City, CO -- | CPM pellet mill base and approx 100hp motor loading fee $50 |
| 3484 | Located in Canon City, CO -- | CPM stainless pellet mill conditioner loading fee $50 |
| 3485 | Located in Canon City, CO -- | CPM stainless feeder with motor and drive loading fee $50 |
| 3486 | Located in Canon City, CO -- | CPM feeder and conditioner last running with a CPM century pellet mill, includes motor and reducer for conditioner loading fee $50 |
| 3487 | Located in Canon City, CO -- | CPM large pellet mill stainless conditioner, last runnign with a 7000 size pellet mill, loading fee $50 |
| 3488 | Located in Canon City, CO -- | Sprout feeder and condtiioner last running on a 501 series pellet mill loading fee $50 |
| 3489 | Located in Canon City, CO -- | Large CPM Conditioner with stainless shell and adjustable paddles, loading fee $50 |
| 3490 | Located in Canon City, CO -- | CPM pellet mill conditioner shroud only (stainless) loading fee $50 |
| 3491 | Located in Canon City, CO -- | LOT 2 CPM pellet mill bases and a CPM door with dual knife posts loading fee $50 |
| 3492 | Located in Canon City, CO -- | CPM pellet mill base loading fee $50 |
| 3493 | Located in Canon City, CO -- | CPM DS Series pellet mill base gearbox and door loading fee $50 |
| 3494 | Located in Canon City, CO -- | CPM 200 series pellet mill mill gearbox loading fee $50 |
| 3495 | Located in Canon City, CO -- | CPM master pellet mill gearbox/parts machine loading fee $50 |
| 3496 | Located in Canon City, CO -- | CPM roughager /century pellet mill no door loading fee $50 |
| 3497 | Located in Canon City, CO -- | CPM pellet mill motor with gear last running on a master pellet mill loading fee $50 |
| 3498 | Located in Canon City, CO -- | CPM 16 pellet mill with door, no motor loading fee $50 |
| 3499 | Located in Canon City, CO -- | LOT 2 sets of CPM Die clamps, force feeder with drive, rolls, and shells loading fee $50 |
| 3500 | Located in Canon City, CO -- | CPM master pellet mill, missing mainshaft assembly and door loading fee $50 |
| 3501 | Located in Canon City, CO -- | cpm feeder stainless steel screw and stainless shell no drive, loading fee $50 |
| 3502 | Located in Canon City, CO -- | Lot: pellet mill clamps, feed cones, and misc parts loading fee $50 |
| 3503 | Located in Canon City, CO -- | CPM stainless feeder and condtioner last running on a century size pellet mill loading fee $50 |
| 3504 | Located in Canon City, CO -- | Lot: 5 sprout 501 die housings, (new replacement cost $9000 each) loading fee $50 |
| 3505 | Located in Canon City, CO -- | Lot: conveyor belting rolls, cog drive belts etc loading fee $50 |
| 3506 | Located in Canon City, CO -- | Pellet mill force feeder with motor (new replacement cost $6900) loading fee $50 |
| 3507 | Located in Canon City, CO -- | Sprout 501 pellet mill force feeder with motor, (new replacement cost $6900) loading fee $50 |
| 3508 | Located in Canon City, CO -- | LOT: (1)Reliance 40hp 3560rpm 460v 0324TSframe (1)Reliance 50hp 3560rpm 460v 0326TSframe Loading fee $50 |
| 3509 | Located in Canon City, CO -- | LOT 4 motors: (1)Baldor 1.5hp 1725rpm 208-230/460v 56Cframe (1)TEFC 1hp 1735rpm 230/460v 143Tframe (2)? loading fee $50 |
| 3510 | Located in Canon City, CO -- | LOT of 3 motors and 2 reducers : (1)TEFC 1.5hp 1745rpm 230/460v 145t frame (1)WEG 3hp 1170rpm 213t frame (1)Leeson 1hp 1725rpm 208-230/460v 56C frame loading fee $50 |
| 3511 | Located in Canon City, CO -- | Large electric motor approx 100hp loading fee $100 |
| 3512 | Located in Canon City, CO -- | Lot: pallet of 5 motors approx 1-2hp loading fee $50 |
| 3513 | Located in Canon City, CO -- | Lot: Motors and motor gear reducers - 3hp reliance motor/reducer, 1/2hp motor reducer, reducer loading fee $50 |
| 3514 | Located in Canon City, CO -- | LOT: Motors with pulley and reducers: (1)Reliance 40hp 1770rpm 230/460amps 324t frame (1)GE .5hp 1725rpm 208-220/440v (1)GE .5hp 1725rpm 208-220/440v loading fee $50 |
| 3515 | Located in Canon City, CO -- | Sprout 21" door and force feeder loading fee $50 |
| 3516 | Located in Canon City, CO -- | CPM hyflo pellet mill with 50hp motor, parts machine missing mainshaft assembly, flange, and change parts. loading fee $50 |
| 3517 | Located in Canon City, CO -- | Newman 150hp 1770rpm 460v 509 loading fee $100 |
| 3518 | Located in Canon City, CO -- | U.S. Electric 150hp 3565rpm 460v 445TS loading fee $100 |
| 3519 | Located in Canon City, CO -- | U.S. Electric 125hp 1775rpm 460v 444T loading fee $100 |
| 3520 | Located in Canon City, CO -- | Electro Dynamic 100hp 1755rpm 220/440v 10 groove sprout pulley 505 frame loading fee $100 |
| 3521 | Located in Canon City, CO -- | U.S. Motor 100hp 1200rpm 440v 587 loading fee $100 |
| 3522 | Located in Canon City, CO -- | Weg 50hp 1770rpm 280-230/460v 326T loading fee $50 |
| 3523 | Located in Canon City, CO -- | Reliance 50hp 1770rpm 230/460v 326T loading fee $50 |
| 3524 | Located in Canon City, CO -- | GE 100hp 1185rpm 550v 584 loading fee $500 |
| 3525 | Located in Canon City, CO -- | Induction Motor 10hp 1175rpm 206-220/440v 284U loading fee $50 |
| 3526 | Located in Canon City, CO -- | Baldor 100hp 1175rpm 575v 405T loading fee $100 |
| 3527 | Located in Canon City, CO -- | Sprout feeder and condtitioner stainleess steel loading fee $50 |
| 3528 | Located in Canon City, CO -- | CPM feeder with stainless shell and screw with approximately 2hp drive loading fee $50 |
| 3529 | Located in Canon City, CO -- | Lot: Lincoln 100hp 1765rpm 230/460v, Teco-Westinghouse 10hp 1765rpm 230/460v, 10hp 1755rpm 208-230/460v loading fee $100 |
| 3530 | Located in Canon City, CO -- | Morse 100hp 1765rpm 208-220/440v 445U loading fee $100 |
| 3531 | Located in Canon City, CO -- | GE 100hp 1770 rpm 440v 504S loading fee $100 |
| 3532 | Located in Canon City, CO -- | Baldor 100hp 1175rpm 575v 405T loading fee $100 |
| 3533 | Located in Canon City, CO -- | Marathon Electric 125hp 3550rpm 460v 404TS loading fee $100 |
| 3534 | Located in Canon City, CO -- | North American Electric 100hp 1785rpm 208-230/460v 405T loading fee $100 |
| 3535 | Located in Canon City, CO -- | Marathon 150hp 3550rpm 460v 405T loading fee $100 |
| 3536 | Located in Canon City, CO -- | General Electric Motor 100hp 440v 3600rpm loading fee $100 |
| 3537 | Located in Canon City, CO -- | US Motor 150hp 1200rpm 460v Fr 1585 with pulley loading fee $100 |
| 3538 | Located in Canon City, CO -- | Toshiba 200hp 1780rpm 460v 447TZ loading fee $100 |
| 3539 | Located in Canon City, CO -- | Reliance 150hp 1780rpm 460v 445T loading fee $100 |
| 3540 | Located in Canon City, CO -- | Large motor approximately 250hp loading fee $100 |
| 3541 | Located in Canon City, CO -- | Worlwide electric 230/460 100hp 60Z loading fee $100 |
| 3542 | Located in Canon City, CO -- | LOT: misc steel parts loading fee $50 |
| 3543 | Located in Canon City, CO -- | Evans 200hp 1700rpm 460v 108S Loading fee $100 |
| 3544 | Located in Canon City, CO -- | US Motor 200hp 1800rpm 440v loading fee $100 |
| 3545 | Located in Canon City, CO -- | Marathon 200hp 1190rpm 447/449T460V loading fee $100 |
| 3546 | Located in Canon City, CO -- | Westinghouse 250hp 1785rpm 460v loading fee $100 |
| 3547 | Located in Canon City, CO -- | Siemens 250hp 1185rpm 460v 449TS loading fee $100 |
| 3548 | Located in Canon City, CO -- | Westinghouse 200hp 1180rpm 460v loading fee $100 |
| 3549 | Located in Canon City, CO -- | Allis 250hp 1790rpm 460v loading fee 507US loading fee $100 |
| 3550 | Located in Canon City, CO -- | Allis 250hp 1785rpm 460v loading fee $100 |
| 3551 | Located in Canon City, CO -- | Pacemaker 250hp 1785rpm 230/460v 449Z loading fee $100 |
| 3552 | Located in Canon City, CO -- | Reliance 300hp 1725rpm 460v 449T loading fee loading fee $100 |
| 3553 | Located in Canon City, CO -- | Toshiba 200hp 1180rpm 460v 505UZ loading fee $100 |
| 3554 | Located in Canon City, CO -- | US Electric 150hp 1200 rpm 460v, loading fee $100 |
| 3555 | Located in Canon City, CO -- | Worldwide 400hp 1789rpm 460v 586/7T Yr-2004 loading fee $100 |
| 3556 | Located in Canon City, CO -- | Feeder with drive, stainless last running with a CPM pellet mill loading fee $50 |
| 3557 | Located in Canon City, CO -- | LOT: motors: (1) Baldor 1.5hp 1725rpm 208-230-460v 145tc frame (1)Toshiba1.5 hp 1740rpm 230/460v 56c frame (1)Baldor3hp 1725rpm 208-230-440v 213 720m frame, gearbox with sprocket loading fee $50 |
| 3558 | Located in Canon City, CO -- | LOT: CPM pellet mill stainless back plate with steel covers and plates loading fee $50 |
| 3559 | Located in Canon City, CO -- | LOT: Reliance 1hp 1725rpm 230/460v R56 frame, with gear dirve and metal frame loading fee $50 |
| 3560 | Located in Canon City, CO -- | LOT: Base last running on a century pellet mill, and a feeder conditioner last running on a cpm pellet mill, loading fee $50 |
| 3561 | Located in Canon City, CO -- | LOT: Bin of stainless feed chutes, slides, boxes etc loading fee $50 |
| 3562 | Located in Canon City, CO -- | Lot: motor fan guards loading fee $50 |
| 3563 | Located in Canon City, CO -- | Lot: Motor fan guard parts etc loading fee $50 |
| 3564 | Located in Canon City, CO -- | LOT: Stiffener ring, plates, etc for sprout or similar pellet mills loading fee $50 |
| 3565 | Located in Canon City, CO -- | LOT: Crate of pellet parts including hoist, coupling, magnet, shear pin outer casting, belts etc, loading fee $50 |
| 3566 | Located in Canon City, CO -- | hammermill guards, misc steel parts, die clamps loading fee $50 |
| 3567 | Located in Canon City, CO -- | Conditioner for CPM pellet mill, stainless steel shaft, like new adjustable paddles, and steam diffusing loading fee $50 |
| 3568 | Located in Canon City, CO -- | Sprout Andritz stainless steel feeder / conditioner with adjustable paddles with approximately 15hp motor loading fee last running animal feed $50 |
| 3569 | Located in Canon City, CO -- | LOT: CPM pellet mill door and bearings, loading fee $50 |
| 3570 | Located in Canon City, CO -- | Die pallet type jack for pellet pellet mill dies loading fee $50 |
| 3571 | Located in Canon City, CO -- | LOT: Stainless screws, stafts, etc, loading fee $50 |
| 3572 | Located in Canon City, CO -- | LOT: pulley, steel plates, feed cone , boxes, steel nut, loading fee $50 |
| 3573 | Located in Canon City, CO -- | LOT: 2 Pallets Misc CPM parts including: die clamps, bolts, coupling parts, rolls assemblies,(feed cone not included) etc loading fee $50 |
| 3575 | Located in Canon City, CO -- | LOT: CPM die clamps, hammermill screen, cog belts, etc loading fee $50 |
| 3576 | Located in Canon City, CO -- | Lot: Misc CPM Parts Primarily for century pellet mill including: die clamp bolts, shear pins, scrapers, roll shafts, spools of wire, shafts, coupling parts, misc steel etc loading fee $50 |
| 3577 | Located in Canon City, CO -- | Lot: misc wire tubes, wires, straps, electrical, rope etc, loading fee $50 |
| 3578 | Located in Canon City, CO -- | Lot: Misc flanges, guards, mild and ss steel, pellet mill and hammermill parts etc, loading fee $50 |
| 3579 | Located in Canon City, CO -- | CPM Century die, approximately 1/2 square cubes, surface rust but appears new/never used, loading fee $50 |
